 | | Re: Still JAVA and LNP....
|
|
Umm in response to my own message, would someone be so kind as to explain the following <g> : // return (short)(a + (b << 8)); return (short)(a % 256); If I use the bottom line, discounting variable b, then my checksum is correct...otherwise it (...) (24 years ago, 3-Nov-00, to lugnet.robotics.rcx.legos)
|
| |
| | Still JAVA and LNP....
|
|
hey all :) Sorry to bother again, but after limited uccess with getting JAVA to cope with LNP, I've run into some (hopefully) simple problems, I'm having major problems with the checksum routine, this routine give me huge integer nnumbers rather (...) (24 years ago, 3-Nov-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: ttyS1 corrupted after using legos
|
|
(...) Frank, I'm also using Linux (Red Hat), and had a similar problem. After using the IR tower, my modem wouldn't work on the same serial port. I solved the problem by not sharing the serial port 8?) which also allows me to connect while using the (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX: Loose Assembly?
|
|
(...) Oh oh. Sounds like a fault. You'd better phone LEGO and get it replaced. Otherwise you'll be unhappy for life. NONE of mine do anything like that. They are, and pardon the pun, built like a brick. Dean -- Coin-Op's For Sale!: (URL) Lego (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Auto Shut Off
|
|
(...) Ok, to set the time out with RCX code you must hit the Oroboros (the sideways 8) and it will never shut off. This can be found under "Getting Started" then the far Right option on the bottom. Hope that helps. Dean -- Coin-Op's For Sale!: (URL) (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Auto Shut Off
|
|
(...) If I remember well there is an option on the RCX Setup (Advanced) page that will allow you to modify (and also switch off) the auto off delay. Jan (24 years ago, 2-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: ttyS1 corrupted after using legos
|
|
(...) Is the only program you are using to download things firmdl3? (...) Try also stty -a < /dev/ttyS0 and/or stty -a < /dev/ttyS1. (...) As far as I know, firmdl3 does not download .lx files. I think there is a separate program for that. dll (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Sticking
|
|
Lego customer service is really good about this (as has been written before on this newsgroup). This is a known problem with this motor. On the suggestion of the various posters, I called up Lego Customer Service (number listed on their web site and (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx, lugnet.technic)
|
| |
| | Re: Motor Sticking
|
|
(...) them (...) hand. (...) When I first got my RIS, on a finny sunny christmas morning :) I eagerly built my first bot, only to watch it veer off to the right, at first I was puzzled assuming I'd messed up the power settings, but eventually I (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx, lugnet.technic)
|
| |
| | ttyS1 corrupted after using legos
|
|
Hi there, I donwloaded, compiled and used legOS 2.4 which worked all very fine. But since then, I cannot use the serial port anymore that I connected the IR-tower to. Maybe anyone has encountered the same problem and knows a solution:) I am no (...) (24 years ago, 2-Nov-00, to lugnet.robotics.rcx.legos)
|
