 | | Motor Masks***
|
|
Hi , does anyone know if there are specific moter masks already defined for the HB? Or can I just initialize them anywhere there is free memory? Thanks -Mike (25 years ago, 9-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | RE: fast computer problems
|
|
Still no luck! any other ideas ??? - what baud rate is the port meant to be set at? 9600? Thanks again Ross -----Original Message----- From: Gary Livick [mailto:glivick@pacbell.net] Sent: 05 June 2000 08:25 To: The Glashans Cc: (...) (25 years ago, 6-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | SCI, IC and interrupts
|
|
Hi I need to communicate with my handy board using the serial port using the Interrupt for SCI. I tried to test several programs that I found, without success. My basic test is the following. 1.- I created and .asm file which is a copy of the (...) (25 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: fast computer problems
|
|
What works on my computer is to go into the port settings, set XON-XOFF, and then enable the FIFO buffer and turn the speeds all the way up. I have a Toshiba laptop, so hopefully your settings will be the same. If I do it any other way under WIN98, (...) (25 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | fast computer problems
|
|
Hi all I jsut got a new win 98 machine, and tried to move IC across to the new machine. I came up against the problem I'm sure everyone with a new PC must have encoutereded with win 98, where IC wont communicate. From DOS IC works perfectly and HBDL (...) (25 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Did I fry my Polaroid unit?
|
|
Today, I started trying to use my Polariod Sonar unit pulled from a Polaroid OneStep Sun 660 Camera. I didn't get the hang of it the first time. I desoldered the connector and put on wires. Then I plugged it in backwards. Oops. The chips started (...) (25 years ago, 3-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Where to find program examples?
|
|
Hi I recently purchased a Hb, does anyone know where I can find examples for programming it? Also is the IC code for the rug Warrior the same as the IC for the HB? Thanks -Mike (25 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Ic question
|
|
As far as I know, the infinite loop construct is the way to do it. However, you can have multiple processes, each waiting on a sensor, each running in an infinite loop, each using the defer() function to allow switching between processes when (...) (25 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Sharp GP2D12 & Sony IR Receiver
|
|
Is there SOMEONE that can run SHARP GP2D12 analog sensor when using IR RECEIVER? I couldn't achieve that. The sensor can give satisfactory results it is used without alone. I can also get data of a sony remote controller from the ir receiver when (...) (25 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Ic question
|
|
I have been playing around with my handy in command line for a little while now. It seems like the only way I can get it to start doing something when a sensor is activated is to have it in an infinite loop waiting for that sensor to be pressed. For (...) (25 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
