 | | RE: fast computer problems
|
|
Still no luck! any other ideas ??? - what baud rate is the port meant to be set at? 9600? Thanks again Ross -----Original Message----- From: Gary Livick [mailto:glivick@pacbell.net] Sent: 05 June 2000 08:25 To: The Glashans Cc: (...) (26 years ago, 6-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | SCI, IC and interrupts
|
|
Hi I need to communicate with my handy board using the serial port using the Interrupt for SCI. I tried to test several programs that I found, without success. My basic test is the following. 1.- I created and .asm file which is a copy of the (...) (26 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: fast computer problems
|
|
What works on my computer is to go into the port settings, set XON-XOFF, and then enable the FIFO buffer and turn the speeds all the way up. I have a Toshiba laptop, so hopefully your settings will be the same. If I do it any other way under WIN98, (...) (26 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | fast computer problems
|
|
Hi all I jsut got a new win 98 machine, and tried to move IC across to the new machine. I came up against the problem I'm sure everyone with a new PC must have encoutereded with win 98, where IC wont communicate. From DOS IC works perfectly and HBDL (...) (26 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Did I fry my Polaroid unit?
|
|
Today, I started trying to use my Polariod Sonar unit pulled from a Polaroid OneStep Sun 660 Camera. I didn't get the hang of it the first time. I desoldered the connector and put on wires. Then I plugged it in backwards. Oops. The chips started (...) (26 years ago, 3-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Where to find program examples?
|
|
Hi I recently purchased a Hb, does anyone know where I can find examples for programming it? Also is the IC code for the rug Warrior the same as the IC for the HB? Thanks -Mike (26 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Ic question
|
|
As far as I know, the infinite loop construct is the way to do it. However, you can have multiple processes, each waiting on a sensor, each running in an infinite loop, each using the defer() function to allow switching between processes when (...) (26 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Sharp GP2D12 & Sony IR Receiver
|
|
Is there SOMEONE that can run SHARP GP2D12 analog sensor when using IR RECEIVER? I couldn't achieve that. The sensor can give satisfactory results it is used without alone. I can also get data of a sony remote controller from the ir receiver when (...) (26 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Ic question
|
|
I have been playing around with my handy in command line for a little while now. It seems like the only way I can get it to start doing something when a sensor is activated is to have it in an infinite loop waiting for that sensor to be pressed. For (...) (26 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Got my Handy, now what?
|
|
(...) The The Handy Board Technical Reference has encoder information for you. The ones I use are the QRB1114, and they are just two or three dollars each. The Reference shows you how to wire them. See (URL) encoders mentioned provide an analog (...) (26 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
