 | | Re: Handyboard Upload
|
|
Here is a RS232 com driver that you can use to send serial data to other devices. It's on the Handy Board Site. (URL) is more info similar to the above, also from the Handy Board site: (URL) there is the attached from George Musser's Advanced (...) (25 years ago, 24-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: InterActive C 3.2 or Interactive C 2.8 freeware
|
|
The commercial version of IC offers the ability to declare multidimesional arrarys (with freeware, you only can use single dimensiond arrays), commercial IC allows #includes, and the user interface is somewhat more robust, making debugging more (...) (25 years ago, 24-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Handyboard Upload
|
|
Has anyone out there ever uploaded data collected by the Handyboard back to the PC? I need to get some distances measured by our sonar sensors back up to the PC for use in another application. If you can help me, I'd really apprieciate it. (25 years ago, 24-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard in mix with SSC II Servo Controller
|
|
Hi again, Don't be confused la. I think you had made a little mistake. In order to interface SSC with HB, the serial connection is not by the telephone line. The connections is done by connecting the serial data pin on the SSC. Remind you that it is (...) (25 years ago, 24-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | InterActive C 3.2 or Interactive C 2.8 freeware
|
|
Hello Handyboard users and helpers, We are a group of new Handyboard users from Denmark. We are building a non commercial autonomus mobile robot (Programmed via PC)for a competition at a university. We need to know wether we can do with the (...) (25 years ago, 24-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard in mix with SSC II Servo Controller
|
|
Hi! I've tried connecting the SSC II to the handyboard through a telephone wire (and when that didn't work) through the configurating header at the upper right corner of the SSC II circuit board. I've downloaded the proper library to the handyboard (...) (25 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | dead hb - alive again
|
|
hello. seems my dead handyboard problem of yesterday was a result of a bad adapter, not the board itself. a relief. thanks, claudia (25 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard in mix with SSC II Servo Controller
|
|
Hi, There are several steps you should follow. 1..Download the 9600 serial driver form (URL) you that if you use SSC controllers, download the inverted version. 2...Refer to you SSC manual, connect the serial in pin to PA7 of handyboard, PA7 is the (...) (25 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | dead hb - overpowered?
|
|
hello. i used the wrong dc adapter (15v) to power my hb today. i made the switch to the proper adapter (12v) fairly quickly, and things seemed fine - i was able to download the pcode. but when i rebooted the board, the power died and i've not been (...) (25 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: resistor pull-up help!
|
|
basically, yes. the inputs from the expansion board feed into the inputs on the main board. if you need a high impedance input, your best bet is to cut a trace on the main board and use one of those inputs. the exp bd takes over main board inputs 0 (...) (25 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
|
