 | | Re: HandyBoard not responding
|
|
Kalyan, During the two weeks that you didn't use your HB did you install any software that uses _any_ serial port? When I installed Windows CE Services it interfered with serial I/O. To talk to other serial devices on com1 it's necessary to disable (...) (25 years ago, 22-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard not responding
|
|
it sounds like it's a problem with your downloader configurations -- neither of them can open the COM port. were you able to connect "Direct to COM1" with HyperTerminal when doing the Windows Serial Debug? it's odd that that would work and then the (...) (25 years ago, 22-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | HandyBoard not responding
|
|
Hi, I left the HandyBoard without power for 2 weeks ,and now I am not able to download anything to it. When I try using HBDL.exe to download pcode_hb.s19 I get the errror "Wrong port or Board mode.". I am using the 12VDC adapter connected directly (...) (25 years ago, 22-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | Re: com1 port settings to download pcode.hb.s19
|
|
I think the IRQ is not ok. ----- Original Message ----- From: lourdes Costa <loucosta@earthlink.net> To: <handyboard@media.mit.edu> Sent: Sunday, November 21, 1999 6:34 PM Subject: com1 port settings to download pcode.hb.s19 (...) trying (...) don't (...) (25 years ago, 21-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | Re: com1 port settings to download pcode.hb.s19
|
|
go to start->settings->control panel->ports and see if COM1 is available, if not then use the the com port that is listed there, if there is nothing there then there is something wrong. Also make sure any background apps aren't using the com port. (...) (25 years ago, 21-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | Re: com1 port settings to download pcode.hb.s19
|
|
did you try the Windows Serial Debug instructions, at (URL) will at least tell you if the serial port is working at all. if you don't see the "Direct to COM1" setting available in HyperTerminal, then Windows doesn't believe you have a serial port at (...) (25 years ago, 21-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | com1 port settings to download pcode.hb.s19
|
|
Hi, I am here struggling to connect the handyboard with my computer. I am trying download pcode.hb.s19 In com1 port, but i am receiving a message that it can't open the port. I think that the settings of my com1 port is wrong. They are: Band rate = (...) (25 years ago, 21-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | IR detection
|
|
hey does anybody know how an IR sensor card works? -- Dovi Poznanski dovip@post.tau.ac.il 22 Israel's st. Tel Aviv tel: 03 5229643 (25 years ago, 21-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Nicad Problems
|
|
(...) Hi My name is Marco and I am not interested to handyboard, but I have a lot of experience with NiCd battery. Whitout more precise data and history of your NiCd cell pack, the highest probability to have a reversal in the polarity is due to a (...) (25 years ago, 20-Nov-99, to lugnet.robotics.handyboard)
|
| |
| | Nicad Problems
|
|
Hi Ive been having problems with my batteries for my handyboard lately so I took them out to check them all. All the batteries checked out fine except for one, which had something very wrong with it - the terminals were reversed! So when I measured (...) (25 years ago, 20-Nov-99, to lugnet.robotics.handyboard)
|
