 | | Re: Running stepper loop at specified (varying) frequency?
|
|
Greg: You can run assembly from within Interactive C, so if IC isn't fast enough for you, you can build in something that is. However, IC will execute pretty quickly in terms of how fast steppers run, so it could be that IC will work for you as-is? (...) (25 years ago, 29-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Help needed reviving my HB
|
|
Igor: Sounds like you have two problems, with the LCD being a separate one from the sync errors. For communicating with the board via IC.exe, try changing your port settings to 9600/8 data/no parity/1 stop/Xon/Xoff/FIFO buffers enabled. I don't have (...) (25 years ago, 29-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Running stepper loop at specified (varying) frequency?
|
|
I am hoping to control some stepper motors with the Handy Board; I will be wanting to control position vs time. Therefore I will be wanting to send out the step control waveforms at varying times (to modulate velocity). Can this be done from (...) (25 years ago, 29-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Help needed reviving my HB
|
|
Hi HBoarders! Can anybody help me with making my HB run? Following the instructions from the assembly manual, there were no problems until installing the memory. Before it, the serial communication worked fine with hbdl downloading the pcode, (...) (25 years ago, 29-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | robotics-for education of learning and injoyment-
|
|
10-28-99 TO WHO IT MAY CONSERN:I AM PERMENTLY DISABLED.BUT I WOULD LIKE TO LEARN HOW TO BUILD A ROBOT.ALTHOUGH I AM WORKING ON JUST THE MEDAL FRAMS FOR 3 DIFFERENT ROBOTS SHAPS TO DEZINES.ALTHOUGH I DONT HAVE ANY BLUE PRINTS ON WHAT PARTS I NEED TO (...) (25 years ago, 30-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: stalled motor detection
|
|
Thanks for pointing out the 'dead reckoning' thing. I meant 'object avoidance'! Heh, I think I'd better make another coffee run... Gary Livick wrote in message <381762F1.D9E4F391@p...ll.net>... (...) (25 years ago, 28-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | speech recognition with hb
|
|
We are attempting to incorperate a speech recognition board with the hb. We have the hb controlling an rc car. We also have the speech reconition board controlling the hb. Here is the problem, the microphone for the speech recognition kit is on the (...) (25 years ago, 28-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Not necessarily the handyboard....
|
|
(...) Of course, if you *really* felt that bad about "pimping," you could've sent that privately and not to the whole list...wink, wink :-) I saw the price of your boards. One word: HOBBIEST I say to heck with the expense of boards, nearly anything (...) (25 years ago, 28-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: 64K UPGRADE
|
|
Yes, you can upgrade your HB to 64K and then use Interactive C on it. After the reset HB operates in a 32KB mode that is compatible with the original HB memory mapping. Your C code, however, shouldn't use the PD5/SS pin on the HC11 as it s used to (...) (25 years ago, 28-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Not necessarily the handyboard....
|
|
(...) <blatant self-promotion> I work for ComputerBoards, Inc., a company that makes high quality yet inexpensive expansion cards for Intel platforms. We have just about anything you could need for analog or digital I/O, serial communications, GPIB, (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
