 | | Re: electronics question please help
|
|
Eric - - You might try shielding the IR sensor ... add successive layers of "Scotch" tape until you get the desired sensitivity. I'm using layers of black plastic trash bags ... it blocks a lot of visible light, but very little IR. - - - Nick - - - (...) (26 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: L.E.D. question.
|
|
Typical drop across an LED is about 1.45v. A unit rated at 5v likely has a build in voltage drop/current limiter (read resistor). I would suggest reading the info sheet for absolute ratings. In general, 'any' generic LED will work. Buy the cheapest (...) (26 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: HB to create video displays?
|
|
At 03:25 PM 2/22/99 -0500, Steve Wall wrote: [snip] In short I want to be able to watch the monitor and have (...) Checkout Decade Engineering's Bob II board at: (URL) I don't think it can do graphics, but it accepts serial input at 9600 baud and (...) (26 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: electronics question please help
|
|
(...) Been there, done that! Funny. I bought almost all the same stuff from my local shack. Writting the software was the easy part ;^). (...) I've supplied some power to the inverter, yes. I'm assuming it's mandatory to have the inverter actually (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: lib_r2.lis ?
|
|
Dear Mr Pennington, Have you configured IC using ic -config command ? This sets the library file and its directory. For handy board, the library file is lib_hb.lis.This is a list file which contains the words lib_hb.c and lib_hb.icb. The lib_r22.lis (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Visual Basic and parallel port
|
|
i know that this doesn't really have anything to do with the handyboard but has anyone tried to access the computer's parallel port with visual basic? =) chen (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: electronics question please help
|
|
Bob - - Here is a link to the 74HCT04 data sheet: (URL) that this helps. - - - Nick - - - Bob Kelly wrote: <snip> (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | electronics question please help
|
|
Hello all, I hope there is a simple answer for this... I have attempted to build the circuit that will allow IR object detection using the Sharp IR detector module and a pair of "high output" infrared LEDs. The circuit I built was the one from (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Book Review ???
|
|
Does anyone have any comments about "The Personal Robot Navigator". It is sold by (URL) about $50. I have read (and continue to read) "Mobile Robots: Inspiration to Implementation" and think it is a *must read*. TIA - - - Nick - - - (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: IR question
|
|
(...) I just looked over the code again, and you're right, I see no reason why it shouldn't work. I guess the comment is just left over from a previous version where it did make a difference. This is not something I can test though, so I'll have to (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
