 | | Re: New Board problems with download
|
|
Hi Luc, yesterday i had the same problem with my notebook (W95). I can´t download to my hb during a session in a full dos-window. With the "MSD.EXE" Programm i found out, i haven´t any COM-Ports (?????). I must configure all COM-PORTS new. After (...) (26 years ago, 26-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: serial transfer
|
|
Most of the commercial telecommunication packages can log incoming data from the com port to a file. Most freeware and shareware versions also do this. Mike (...) (26 years ago, 26-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Where?
|
|
Can i know where to download Freeware IC ......as i need to get started with my mobile robots....in using the 68HC11.? May i know normally how do u all guys do simulation of the robot's movement? Thanks ! Regards, Linnar (26 years ago, 26-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Infrared Sensors
|
|
A few weeks back I was a little dissapointed in the performance of the QT refective optosensors which come with the Handy Board because when using them on the digital inputs, their range was only 1/4 to 1/2 inch or less. Some people told me to use (...) (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo w/ >180 travel?
|
|
Assuming you mean R/C model servos, take a look at the Futaba servos for sail boat winches. Stock Number Description Torque Speed Weight Dimensions FUTM0099 S5801 Sail Winch 136.0 oz. .5/turn 2.9 oz. 1.81 x 0.98 x 1.73 in. Looking at the spec sheet (...) (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Servo w/ >180 travel?
|
|
Do you know of any servos with 180 degree travel or more? 360 degrees of travel would be nice. Thanks Chad Humberstone EUCLID Mobile Robot Lab BYU (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: stepper motors
|
|
(...) Its my code and you are quite right - it is not the best in the world. It was only intended to illustrate a point and I have done no more work on it since then - sorry. When first powered up the steppers will align themselves according to the (...) (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: New Board problems with download
|
|
Luc, it sounds like its not downloading at all. make sure the port you are using is not disconnected internally, such as when you are trying to use com2 and the internal modem is configured to use com2, usually com2 port is disconnected for external (...) (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: finally got the download working
|
|
From: Brett Anthony <anthonyb@ecs.csus.edu> (...) "slapped around", is that a term they teach at School of Engineering and Computer Science:-) I doubt if the problem is with the 68HC11. H/W and S/W usually work consistantly, as designed. Working (...) (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | New Board problems with download
|
|
Hi, I just received my Handyboard and i'm trying (hard) to get it working. Tried to download the pcode_h.s19 using both the windows downloader and the dosload 'dl.exe' windows one works OK, the dos one works OK but in full dos mode without the (...) (26 years ago, 25-Jun-98, to lugnet.robotics.handyboard)
|
