 | | (no subject)
|
|
Hey Chuck, Being the lazy person that I am I modified another servo instead of figuring out the problem w/ the other one(I'll check it out later...) THE PROBLEM IS SOLVED!!!!!!! They both run much closer in speed. Now I'm off to get the rest of the (...) (27 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Magnetic card readers
|
|
Thanks for don't replly to none of my e-mail!!! All it's cool , but i can accept nobody know wath i answer??? Well i really want somebody tell me: "well i don't want to reply you" . I can do work the reader with code in c , and i want to know how i (...) (27 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo as drive motor
|
|
(...) Because the servos are closed systems they don't have a hard requirement that their motors run at the same speed, however it would affect the slew rate which is spec'd so they have to be reasonably close. If you zapped the capacitor and turned (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | stepper motors
|
|
Hi, Thanks for all the responses regarding CdS photo cells. Now I am considering using stepper motors in my project as well. I have seen some postings on this list before regarding these motors. Can anyone point me in the right direction for (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo as drive motor
|
|
(...) I'll try to replace the caps and see if there is an improvement. I was thinking that when I melted the new leads to the motor I may have left the iron on it for too long, thus burning up the caps. I'm going over to my dad's shop to work on (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: CdS cells
|
|
(...) It's certainly easiest to start out with a sensor that has a reasonable resistance range. However, if for whatever reason you have sensors that tend to be lower in resistance to the ideal, simply add your own resistor between the signal and (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Servo as drive motor
|
|
Hello, I have modified and connected 2 servo motors to the handy. The speed of one is much slower than the other. I swiched the motors around (first in Port (0),and (2) ) and then the reverse and the same motor is slower ... could I have fried the (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: CdS cells
|
|
David, I believe you will want to purchase ones that have a dark resistance more than say 20K. The sensor is part of a divider circuit that includes a 47K resistor. The sensed signal equals (sensor resistance)/(sensor +47K) multipled by 255. If your (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Obtaining a Handyboard in the UK
|
|
I just wanted to say that I ordered the HB from Hong Kong on Monday. I sended the money via my bank account and paid £12 for money delivered in 5 working days, or £17 for two. It containes: Kit A DB-9 or DB-25 (please select one of them, this (...) (27 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: 3v motors
|
|
Yes Vs should stay at 5v, but if you read my original message the best thing is to use 9.6 volt motors!! Save yourself some trouble! jm (...) (27 years ago, 7-Aug-97, to lugnet.robotics.handyboard)
|
