 | | What a day.
|
|
Well I wanted to demo my new robot it was cool, but the day did not turn out to well. I think I switched the phone cables. When I tried to connect my interface board with the HB, it would not run IC. I then tried to download a new PCODE_HR.S19, but (...) (28 years ago, 28-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
1. Is it possible to expand the 32K RAM of the Handy Board? If so, how? 2. We will be using two shaft encoders (HEDS5500 from Hewlett-Packard) for our project. How can we interface the shaft encoders to the Handy Board? What inputs do we use? Does (...) (28 years ago, 28-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Power Supply
|
|
I'm using the 1.2 volt NiCad's wired in series to give me 9.6 volts. If I want to get rid of one or two of the batteries, will the handyboard still run at 7.2 or 6.0 volts ? What is the minimum voltage that the handyboard will run on, 5V ? I dont (...) (28 years ago, 27-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Unsubscribe
|
|
Please drop me from the list. I can't handle the volume. Ken Owen (28 years ago, 27-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | as11
|
|
Can anyone tell me how to get the Motorola freeware assembler for the HC11, to run on a PC? Thanks Richard Whitehead (28 years ago, 27-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Mobile Robots book
|
|
I recieved my copy in a special deal from a book club that catered to electronics enthusiasts. It was a kind of Book-of-the-month club. The name escapes me at the moment. Anyway, you got to choose 3 books for like $5. Then you just had to buy one (...) (28 years ago, 27-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector 2x again
|
|
(...) You'll need 3 input and 2 output lines. One input and two outputs are available at the SPI port, (right side of board, J6?). Find two more discrete inputs on the Handyboard and you're set. All the other inputs on the V2X can be hardwired high (...) (28 years ago, 27-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Vector 2x again
|
|
I know this topic has come up time and time again, but from all the previous postings I still am unsure of some things. First of all has anyone be able to get the vector working *without* using any other microcontroller board (using only the (...) (28 years ago, 26-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: -POWER-GLITCH-
|
|
Make sure your downloader is configured to download "pcode_hb.s19" and not any of the other variants (eg pcode_r22.s19). Avard, please send me an email and let me know if this solves your problem. -Fred In your message you said: (...) (28 years ago, 26-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: memory not remembering...
|
|
Ben -- the pin 27 R/W line of the RAM should be connected directly to the R/W line of the 6811. I don't remember the pin # off hand -- it's 7 i think -- but just check the schematic. check the continuity first on the board. if that's ok, then check (...) (28 years ago, 26-Jan-97, to lugnet.robotics.handyboard)
|
