 | | Some sensor and misc ideas
|
|
I stumbled on these addresses and thought I would pass them along. I found the idea of using a mercury switch a really cool idea. Many possibilities with that idea. also some pneumatic valves there havent looked at them much yet. (URL) someone finds (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Surveillance Robot
|
|
Check this Lego Dacta set: (URL) uses the Lego Dacta Control Lab, not the RCX, but still, it's a Lego set with a B&W QuickCam, for a similar Mars exploration mission. Price for this set is $379. Given that the Lego Dacta Control Lab is $675 (roughly (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Some sensor and misc ideas
|
|
Shane, (...) This sounds like a great idea that would bring MS back into the forefront vs CyberMaster (this uses a radio link) in my opinion. Are you sure it works though (I guess you must be). I thought the brick and the tower maintained two way (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | re: re: moving in a straight line with two motors
|
|
G'Day if any body is still interested in this, check out (URL) down near the bottom for an implementation using two differentials and a locking clutch to keep them in sync. Drawback is that all three motor outputs are used up. (or perhaps a small (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Happy Thanksgiving Everyone!!
|
|
and to all your loved ones!!! John C. locutus@frontiernet.net (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Surveillance Robot
|
|
(...) I agree, but my impression was that this expansion too was going to be $50. (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Air Tanks
|
|
Shop@Home doesn't have a Service pack with the tank in it. I asked. To get one I had to buy an 8250 (Submarine). It was worth it to get long yellow beams and some more pneumatic parts. The tank works great with the 5107 pump. The compressor (5117) (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Air Tanks
|
|
Nancy, take a look at my compressor (dual) design and comment... www.bmts.com/~rhempel And follow your nose to the LEGO stuff... Cheers, Ralph Hempel - P.Eng ---...--- The train stops at the train station, The bus stops at the bus station, So why am (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: MindStorms rotation sensors
|
|
(...) And?...... (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: legOS
|
|
(...) Firmware isn't software??? Go way back when and see what happend to bring about the IBM PC clone. The BIOS reverse engineering and why MACs haven't been cloned. Firmware *is* software, placed in a chip instead of 'normal' media (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Worm Drive Question
|
|
The pitch and profile on a worm gear *is not* that of a threaded rod. Yeah it works, but at what cost to the parts? (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Air Tanks
|
|
Very cool Ralph! I only ordered one compressor because I thought it was a big as the pump. I'm planning to get some more. The valve question is the big one now. I bought a couple of solenoids and I'm still thinking about the valves I found on the (...) (28 years ago, 26-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Worm Drive Question
|
|
(...) So leave the worm gear off and use the threaded rod exclusively. Daniel "Dan'l" Miller Senior, School of Aeronautics and danielmi@expert.cc.purdue.edu Astronautics, Purdue, Indiana danielmi@cartoon.ecn.purdue.edu (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Automatic transmission update
|
|
I've redesigned the automatic transmission and made it much more compact with lots fewer gears. (I hope to take pictures of this and load it somewhere...) A big breakthrough was to change how I combined the high and low gear with a differential. (...) (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Re: legOS
|
|
I had a similar problem, I was downloading with Internet Explorer (I think). I tried the other browser (Netscape, I believe), and all was fine. I think the file was being sent in text mode rather than binary. I may have the browsers switched here. (...) (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Air Tanks
|
|
(...) Nancy, How ARE those solenoids working out, and how much are they? Did you read my comments regarding the fully pressurized state of one port with no neutral? Does this even matter? Inquiring minds want to know.... Cheers, Ralph Hempel - P.Eng (...) (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Air Tanks
|
|
(...) I haven't tried them yet. There's some engineering involved to make them useful. Not even sure I can. (...) I did. The LEGO valve also vents the opposite port when it pressurizes the other. --- Nancy (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Re: legOS
|
|
(...) I don't think whether license agreements/intellectual property rights apply to firmware is being questioned. Just whether the license provided by Lego even says anything at all about the firmware. (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Re: legOS corruption
|
|
(...) I have code that should just increment/decrement some counters and display them. The numbers get reset to strange values. This looks like stack or register corruption, but I haven't yet found where or why (yet). Wish I still did embedded (...) (28 years ago, 27-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Air Tanks
|
|
Nancy Evelyn Gold wrote in message <365E2D7A.BE82A1C4@sgi.com>... (...) Actually, all pneumatics must vent the opposite side. What is keeping you from "engineering" the solenoids. Maybe I can help. I've done lots of pneumatics with "real" systems. (...) (28 years ago, 27-Nov-98, to lugnet.robotics)
|