 | | Re: Flex Cables (was: Does anyone has the 8479 bar code truck? —Dave Baum
|
| | | (...) The reason I speculated that it may have been a legal issue is that several years ago the flex pack was advertised as available from S@H. For some reason they pulled it from US distribution but kept it in Europe. The flex pack has several (...) (25 years ago, 12-Oct-99, to lugnet.robotics)
|
| | | |
| | | | | Re: Flex Cables (was: Does anyone has the 8479 bar code truck? —Mark Koesel
|
| | | | Dave Baum <dbaum@spambgoneenteract.com> wrote in message news:dbaum-111099212...act.com... (...) The "type I" connectors were pulled from the market in the US. There was in fact some legal issue -- something about a choking risk. I forgot where I (...) (25 years ago, 13-Oct-99, to lugnet.robotics)
|
| | | | |
| | | | | | Re: Flex Cables (Does anyone have the 8485 CCII) —Phil Watt
|
| | | | Thanks to Kevin the 8485 Control Center II scans are available and I can finally build the T-Rex. I assumed no-one would want to part with these cables, so I found a way to make my own length of flex cables with 0.065 string trimmer line, making the (...) (25 years ago, 15-Oct-99, to lugnet.robotics)
|
| | | | |
| | | | | | Re: Flex Cables (Does anyone have the 8485 CCII) —Rob Doucette
|
| | | | | Can someone post a side by side comparison of Type I and II connectors?? I have the 5118, 8485, 8412, 8437, and they all have the same connector ends. I'm trying to figure out the difference. Phil: I'll try to get you the mm dimensions for the (...) (25 years ago, 15-Oct-99, to lugnet.robotics)
|
| | | | | |
| | | | | | | Re: Flex Cables (Does anyone have the 8485 CCII) —Phil Watt
|
| | | | | | Thanks Rob, The type I and II connectors can be seen at: (URL) flex cables are also shown with the "pssible" lengths for the 8485. When I scaled the cable on page 110, I came up with 17.2cm (and it came-up short when I built that assembly), but the (...) (25 years ago, 15-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | | | Re: Flex Cables (Does anyone have the 8485 CCII) —Rob Doucette
|
| | | | | | Phil Watt <wattsup1@earthlink.net> wrote in message news:38073CB0.716941...ink.net... (...) I know all of the listed sets use the Type II. I believe the 5118 is Type II as well, I'll verify tonight along with the 8485 cable lengths. -Rob. (25 years ago, 15-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | Re: Flex Cables (Does anyone have the 8485 CCII) —Soh Chio Siong
|
| | | | (...) Happened to be carrying out a parts inventory of my #8485 CC (*not* CCII) which recently arrived from DYA France. Here are the actual measurements of the flex cables - overall lengths followed by the lengths between the notches, in (...) (25 years ago, 16-Oct-99, to lugnet.robotics)
|
| | | | |
| | | | | | Re: Flex Cables (Does anyone have the 8485 CCII) —Rob Doucette
|
| | | | C S Soh wrote in message <3807D69E.34C3F7E3@s...com.sg>... (...) followed by (...) from the (...) I concur! -Rob. (25 years ago, 16-Oct-99, to lugnet.robotics)
|
| | | | |
