To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6586 (+10)
  Re: MindStorms at Robot Store (Hacking Lego Compatible Parts)
 
(...) What about 2.5mm or 3.5mm phono plugs/sockets? Or even the small black plastic blocks like a PC's Reset switch, Power LED and internal speaker use? Amos "Long time listener first time caller" Bieler Look at my address umop episdn and turn (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  Re: RCX Programming Questions and Sensor Ideas
 
I hope someone reads this reply to a reply to a very OLD message. I've been lurking for almost a month and, during a search, I found a thread I can expand. (...) [snip] (...) It is more difficult than this to recognize speech, but it can be done. (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]
 
(...) (snip) (...) I managed to use this touch sensor "feature" as sort of a poor man's bend sensor to improve my wall-following robot. It's a torbot-type design with a left and right feeler-type bumpers in front. Using NQC (thanks, Dave) I set the (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]
 
Some corrections to my last post: (...) should be: turning LEFT when greater than 1000, the robot kept its left feeler against (...) should be: spent most of the time between 101 and 110. (Once TRACKING the wall, I never *saw* (...) should be: (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  MacNQC for 64k Macs
 
Hallo Dave, for playing and programming Lego RCX I would like to use my older Macs, a PowerBook 190cs and Macintosh IIsi. So my children could use my 9500 while I am using Legos with the smaller ones. Also there is no chance to get ROBOLAB from Lego (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  Re: Touch Sensor as a Switch
 
(...) Connecting N touch sensors in parallel requires N pieces of wire, while doing so in series requires N+1 pieces of wire. See? It's not that bad. Here is my experimenting results of connecting the three Cyber Master touch sensors to RCX in (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  motor speed control
 
I have added another web page, this time discussing a way to control the speed of a motor that actually gives you a wide range of speeds. (URL) are no pictures and I had to re-type the NQC code by hand, but the method works fine; I tried it last (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  Re: MacNQC for 64k Macs
 
I should add a link to the docs from the MacNQC page - sorry. The general NQC 2.0 beta test page has some documentation as well as a MPW tool version of NQC that should run on 68k macs: (URL) docs are very brief - mostly just a list of differences (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
 
  Re: ideas for a RIS 2.0 - Rechargability
 
I tried NiMH batteries in my RCX. It lost its firmware. I suspect the output voltage (6 x 1.2 = 7.2) is too low. You should be able to do it using an external battery pack, but I suggest you use 8 cells instead of 6. The resulting 9.6 volts shouln't (...) (27 years ago, 28-Aug-99, to lugnet.robotics)
 
  Re: MacNQC for 64k Macs
 
Ralf, I am running the NQC tool (via MPW) on a 8MB SE/30. I'm using System 7.1 with MPW 3.4.1 (from ETO 20). It works, although things are pretty squeezed into ram. Ray Sanders rsanders@gate.net (...) (27 years ago, 28-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR