To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6561 (+10)
  RE: Touch Sensor as a Switch
 
(...) Can you describe that? Are you connectiong the Lego wires with only one stud overlapping? I don't have software to display your LDRAW file. (...) Very, very interesting. I wonder why that is? Maybe Cybermaster has really only one analog input (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
 
  Re: Q:Best approach to line tracking
 
This is mainly for people who still want to stick to just one light sensor -- You can still figure out which way to turn even with just one sensor, by following the edge of the line rather than trying to follow the center. This works only if your (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
 
  Re: Q:Best approach to line tracking
 
have you tested this approach? it seems like it would work, but the light sensor would have to be fairly far off the surface to get a wide viewing area. it seems it would also get a little hairy with the inconsistency of lighting to determine (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
 
  Re: Touch Sensor as a Switch
 
(...) It consists of one touch sensor and three connection wires. The plates overlap each other by two studs, but because of the orientation of the metal part in the stud, only one stud is actually conducting. The drawing in JPEG is available (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
 
  Re: Q:Best approach to line tracking
 
(...) No. I read about it on web page that describes someone's line follower. They said they had gotten it to work. Sorry, but I don't know the URL -- I've seen so many line followers I can't keep track. (...) Sensor height, speed and line width all (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
 
  Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]
 
(...) I don't doubt that there are reasonable creations that e.g. press a touch sensor button halfway for extended periods of time, but I can't think of any off the top of my head. Can anybody help me out here? My point was that in what I would (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]  [DAT]
 
(...) Okay, I felt like I had some time, so I looked into this a bit. I skipped the first part and jumped right into measuring a waveform. I measured a faster waveforms for now, but might give it another go with a longer waveforms and higher (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  RE: Touch Sensor as a Switch
 
In response to my own post on the Cybermaster touch sensors: The three different Cybermaster touch sensors have a resistance of 15k, 12k, and 10k when not pressed. The rest of my ramblings were pure fiction. The three Cybermaster inputs are (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
(...) Have you tried combining the inputs of the two output motors into a differential? If the inputs are counter-rotating, the net differential body rotation will tell you which side is moving faster, ie: Motor A ------> Differential <--(Reversed (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Use a RCX as a Sensor port AND a Motor Output!
 
So, I was messing around w/ the RCX and hooked up a Micromotor to one of my output ports and lo and behold....I could control the motor by toggling the Sensor Type for that port between a Passive (None, Switch, Temp) mode = OFF and an Active Mode (...) (27 years ago, 26-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR