To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6521 (+10)
  Re: ideas for a RIS 2.0
 
(...) If that were true, then the following multi-touch-sensor adapters would not work: (2 URLs) Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Obj.: r/c servos
 
To add more to all those servo information, I've build a servo controller which use the printer connector on the PC. It doesn't use any electronic, everything is made by software (Delphi 3.0) It is quite usefull to try this at home since you'll (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: ideas for a RIS 2.0
 
(...) gradually depress the sensor. There is not a sharp cutoff like there is with a typical contact switch. I tried building a touch sensor multiplexor, but I was unable to reliably get even 3 to work because the minimum resistance is quite large (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  RE: ideas for a RIS 2.0
 
(...) But it IS true, and that's why the 6 input mux at: (URL) has some problems. Find out for yourself by putting a meter across a touch sensor. The resistance changes from about 1K to 470R when pressed depending on how hard it is pressed. Michael (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Macintosh IR cable
 
Hello, I just talked to Pitsco LEGO DACTA. I was curious about the IR tower they sell, because it comes with a Macintosh cable. It turns out that the cable is available separately, item 4119830, for $15. This item is not listed in the catalog (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  RE: ideas for a RIS 2.0
 
(...) Yes, it's one of those rubber things. Cybermaster's touch sensors come with a translucent housing, so you can see the inards quite nicely. There's a resistor across the two contacts, too. Tilman -- Did you check the web site first?: (URL) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Re: All-LEGO stepper motor
 
(...) Thanks! I'm looking forward to hearing about yours when you've got it built, what you changed and how it works. One of the best things about this (doing LEGO work on the Internet) is seeing different people do the same thing in different ways! (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Re: Q:Best approach to line tracking
 
(...) just program your robot to turn the opposite way as the sensor that goes off the line. i made a line tracker with one light sensor that had treads instead of wheels. when it got off the line, it started roving back and forth (more and more (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  touch sensors aren't just switches (was Re: ideas for a RIS 2.0
 
(...) Wow. That's pretty darn disappointing. I even bought extra touch sensors to use in multiplexed designs (but I haven't made the multiplexer yet). I guess I'll have to build some of my own touch sensors... I wonder why LEGO designed the touch (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
 
  RE: touch sensors aren't just switches (was Re: ideas for a RIS 2.0
 
(...) Many "buttons" in today's electronic devices are designed that way. Check your TV remote control, your key-chain remote control for your garage door opener or car alarm, the buttons on your phone etc. It eliminates the need for a physical (...) (27 years ago, 25-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR