To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6476 (+10)
  Re: r/c servos and firmware
 
(...) Almost exactly how I'd do it. The problem is what if OCIB must be set to a small value, and the FRT has already passed this value when the OCIA handler sets up OCIB in step 3? This problem is solvable. If the total interval is closer to 1 ms, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) Let's say a 0.7 ms pulse results in a rotation of 0 degrees. Let's say a 2.0 ms pulse results in a rotation of 180 degrees. If all you had were 0.7 ms pulses and 2.0 ms pulses, you'd be able to choose either 0 degrees or 180 degrees, resulting (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Exactly. See (URL) examples. These servos have a little disc or cross on top with holes at the edges. The servos can turn the disc only 45 degrees in each direction. They are used for moving flaps or rudders on model airplanes. You bend a 90 (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Whew! I'm glad I got that much right :-) (...) We could check OC1B and if it's "close" just turn off the motor...as far as the long timer goes, OC1A should always force the output off...on the other hand, the OC1B could be set NO GREATER than (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) In (...) make (...) least (...) Hello, New mindstorm user...been lurking for a while. WRT to servo motion -- it is fairly easy to modify standard servos for continuous motion. $ would put this motor about the same cost as lego so not sure of (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Thinking about this more, I do not know what I was thinking earlier. Since you are in an ISR, you know can count the number of cycles in the instructions between reading the FRT and enabling the OCIB interrupt, and you can estimate "close" (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: Using RCX with Lego Trains
 
Hello, I have used my RCX to control my Lego train using the wall wart for the train for power. You can run the train off of the bateries but it is pretty pathetic. (I did it once by accident.:)) I set up a simple oval track that used th e light (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: New web pages
 
(...) LOL! I love your expert assitance on the page for the ball-axle connector! Cheers, - jsproat (27 years ago, 21-Aug-99, to lugnet.build, lugnet.robotics)
 
  Motor Speed/Torque Sensor
 
I've developed a circuit that can be used to measure the speed of a powered motor. It works by measuring the voltage generated by the motor during the off period of the PWM. Since the highest power output setting is on all the time, it doesn't work (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  robotic rovers
 
Hello all, I'm trying to construct a rover to make its way around a household environment and avoid obstacles reliably. I'm experimenting with several chassis designs to find one to my liking. (Okay, so I build one design, try it for five minutes, (...) (27 years ago, 22-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR