To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 541 (+20)
  Re: Homebrew sensors?
 
(...) So's Michael - he's proposing a notch filter so you get the amplitude at a particular frequency, which may be better for a seeking application. Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) I think making the pendulum longer should cure this... (...) Possibly making it heavier will cure this... Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
In article <Pine.GSO.3.96.98111...129.6050E- 100000@expert.cc.purdue.edu>, Daniel Miller <danielmi@expert.cc.purdue.e du> writes (...) Ah. A jet engine expert. It always puzzled me how the hot air knows it is supposed to go out of the hole at the (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
does pressure difference make any sense?..:-) Selçuk (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
---...--- (...) attached. (...) is (...) is (...) sheet (...) I expect that the "motor is shorted" state is achieved by turning on either both high-side drive FET's or both low-side drive FET's, and niether of these combinations would provide a high (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Cybermaster protocol?
 
(...) If I'm not mistaken, Peter Ljungstrand has compiled this information at (URL) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Mindstorms meeting in Boston
 
Hey -- any Boston area people should come to the Construction Site tomorrow (Nov 15) from 7-9 for a Mindstorms show-n-tell/get-together. Details (such as there are) on lugnet in lugnet.loc.us.ma.bos (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  How to receive messages from the CuberMaster unit?
 
I'm currently using Dave Baum's NQC on a Linux system with CyberMaster (thanks to Peter Ljungstrand's adaption), and am very happy with that. However, I often find myself in the position where I want to transfer data from the CyberMaster mobile unit (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Image processing? Proportional control pushes back proportional to deflection (i.e. it simulates a spring). Derivative control pushes back proportional to rate of deflection (i.e. it simulates dynamic friction). Integral control pushes back (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Perhaps you're asking too much of them. Try toning down the pendulum; that is, give it some length below the hinge point as well. As long as it's still top-heavy you're still technically an inverted pendulum, and the added mass below the pivot (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Alex Wetmore wrote in message (...) If you are thinking pneumatics and mindstorms, you might check out an electric pneumatic switch (made in Lego) at (URL) it is interesting to note that the piston of a fully charged and extended cylinder will (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
-- ===...=== Don Forth ( Klaatu ) email: dforth@caro.net Home Page: (URL) Brandwine wrote in message ... (...) Check out - (URL) has an example of a treaded vehicle that uses this type of system one motor for forward and backward motion and one for (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  RE: moving in a straight line with two motors?
 
Carl G. Schaefer, Jr. <lego-robotics@crynwr.com> wrote (...) By making sure the magnets are not strong enough to do those things. Which isn't hard - it takes a very strong magnet to interfere with solid state electronics. It's only magnetic media (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Tim, I used a quick and dirty technique to create steering maps for a robotic car when I was an undergrad at RPI and it sounds like you've got all the ingredients you'd need to do the same thing. Essentially you need to tow a trailer behind your (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Online ordering available
 
(...) The discount is the time you have to wait........ Is it not scarce? Do they not have them in stock? Soooooo, they discount the waiting period......... Sorry, I am just being silly..... (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: MindStorms on NT / trouble posting to the list
 
I've been running the MindStorms software under NT, and I haven't had any trouble at all. I don't think that NT is formally supported by LEGO, but its been just fine for me! -----Original Message----- From: Eric Eilebrecht <ericeil@microsoft.com> (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
 
  Re: MindStorms on NT
 
(...) I'm not using the LEGO software anymore since I discovered nqc, but I remember it was very slow on a P120, taking 100% CPU all the time. Typing (sleep-times, filenames...) also didn't work the way it should, it was very slow and didn't display (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
 
  RE: MindStorms on NT / trouble posting to the list
 
I have been using NT with mindstorms for two weeks now, and I have yet to find a problem with it. bradley green (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
 
  No discount? (was Re: Online ordering available
 
(...) Well, it may or may not be scarce. I have in the last two days been to the Learningsmith in Cherry Creek Mall, Denver CO, and the Learningsmith in Woodland Mall, Kentwood/GR, MI, and both of these fine establishments have at least 3 of the (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
 
  Spirit.OCX & Starting a Program
 
If I want to start a program using spirt.ocx do I use StartTask (number) ? I've been trying to use this with no luck. And would appreciate some help with this. (28 years ago, 15-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR