 | | Re: Lab View
|
|
As far as I can tell Robolab is really a slightly trimmed version of Labview, with the bulk of the standard Labview VIs removed. More important however, is the fact that since the RCX is a remote device, you don't really make use of it in the same (...) (27 years ago, 19-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Lab View
|
|
Thanks for the info Rob. I have acces to both labview 4.1 and 5. This is also the only code I can program in at the moment, and starting to use it quit a bit at work now. I have done C, assembly, and Pascel but that was years ago. I guess this would (...) (27 years ago, 19-Jun-99, to lugnet.robotics)
|
| |
 | | Re: multi-RCX dreaming
|
|
I find some of the most interesting material on the topic of robotics, as well as Autonomous Behavior and AI, are books on genetic algorithms and natural selection programming. Very interesting to consider, for instance, programming a group of bots (...) (27 years ago, 19-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Lab View
|
|
In a message dated 6/18/99 8:07:18 PM Eastern Daylight Time, robkc@home.com writes: << As far as I can tell Robolab is really a slightly trimmed version of Labview, with the bulk of the standard Labview VIs removed. More important however, is the (...) (27 years ago, 19-Jun-99, to lugnet.robotics)
|
| |
 | | MIT handy board or laptop..
|
|
I have be thinking of the next step up to take after the lego rcx. It seems like the more I use it the more I want more sensor inputs and more motor controls ect. I was looking at the MIT handy board it looks like a good way to go but what about (...) (27 years ago, 19-Jun-99, to lugnet.robotics)
|
| |
 | | Re: MIT handy board or laptop..
|
|
(...) The handyboard is lighter, cheaper, and has I/O ports designed for robotics. With a laptop you would have to interface some sort of I/O card for your sensors, mostly likely through the parallel port since it is the easiest device to interface (...) (27 years ago, 19-Jun-99, to lugnet.robotics)
|
| |
 | | Re: MIT handy board or laptop..
|
|
(...) Perhaps, but you'll find that there aren't that many more ports available easily. With effort yes. (...) Indeed. Handyboard, Botboard, Fingerboard, and LOTs of other HC11 as well as 8051 stuff is out there. Your programming environment gets a (...) (27 years ago, 20-Jun-99, to lugnet.robotics)
|
| |
 | | using nqc for first time
|
|
Hi all- Need some help troubleshooting this: I'm trying nqc on the Mac, and so the first thing I did was try the test program that came with it, but I'm getting weird errors. I should preface this by saying that my current setup of cables, IR tower (...) (27 years ago, 20-Jun-99, to lugnet.robotics)
|
| |
 | | Re: using nqc for first time
|
|
(...) Very strange. I've heard of some problems with *long* programs failing to load, but never with something as short as test.nqc. Try the following command and e-mail me the results (dbaum@enteract.com) nqc -d -l -v test.nqc (this will print a (...) (27 years ago, 20-Jun-99, to lugnet.robotics)
|
| |
 | | Re: using nqc for first time
|
|
(...) Cool. Thanks for checking this out. I did get one failure, and then one success, and here are the outputs: nqc -d -l -v test.nqc *** Task 0 = main 000 InType 0, Switch 32 00 01 003 InMode 0, Boolean 42 00 20 006 OutDir A, Fwd e1 81 008 OutMode (...) (27 years ago, 21-Jun-99, to lugnet.robotics)
|