To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 506 (+10)
  RE: moving in a straight line with two motors?
 
I might be able to use this solution for another problem. My wheeled bots have a strong tendency to go in whichever direction is necessary to run into sleeping cats. Straight line, pull to right, pull to left -- as long as there's a sleeping cat in (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  RE: moving in a straight line with two motors?
 
Carl G. Schaefer, Jr. writes: > Ah-Oh... > > Magnets in close proximity to the RCX brick may not be a wise idea. On just > about all of my mobile bots, the motors are immediately adjacent to the RCX > brick. The RCX has no magnetism-sensitive parts, (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) <snip> (...) Hey, sounds like goal right up there with the Mindstorms commercials - shoving all the plates off the dinner table, snapping pictures of women in the shower, etc. Great to see the big problems being solved on this list....:-> (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) So _that's_ what they mean by a "pussy magnet"! (Sorry, sorry, I just couldn't resist). Cheers, Ben. (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  RE: moving in a straight line with two motors?
 
Uhh --- that was a stupid comment, wasn't it? How do the Lego guys guard (or shield) against the possibility of the motor magnets disrupting the electronics or memory onboard the RCX? Carl (with a very red, I-can't -believe-I'm-an-engineer, face) (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Tim, Instead of using the differential for angle sensors, why not use it to allow a single motor to drive both wheels? Then a single angle sensor coupled with a motor could drive the steering mechanism. This setup would be very similar to a radio (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) At one point, in the distant past, I saw plans for a gear box that used either 2 or 3 differentials, I do not remember which. 2 motors were used, 1 to drive both axles, one for steering. axle1 == motor1 + motor2 axle2 == motor1 - motor2 With (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  Direct Motor driver
 
Thanks to the fine people who figured the memory mapped motor I/O address to be 0xf000 and who determined the controlling bitmaps, I wrote a native motor driver today. See (URL) missing for a V0.1 kernel release: - task switcher IRQ reassignment (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  RE: moving in a straight line with two motors?
 
-----Original Message----- From: Eric Brandwine [SMTP:ericb@mitre.org] Sent: Friday, November 13, 1998 8:39 AM To: John Scott Kjellman Cc: lego-robotics@crynwr.com Subject: Re: moving in a straight line with two motors? <snip> (...) I don't think it (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
From: John Scott Kjellman <jkjellman@ameritech.net> (...) The main downside with this approach is that you can't turn on axis (so your vehicle will no longer have a turning radius of 0). When I first got the mindstorms I thought that it would be (...) (28 years ago, 13-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR