 | | Re: Angle Sensor
|
|
(...) So long as your software remembers to count the revolutions, it's surely very simple to gear the Lego sensor to get a real angle... however for your idea below, you might need much too much gearing! (...) You shouldn't need fuzzy logic to do (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | Light Sensor Non Destructive Mods
|
|
Hi All, I've just added a new page to my website that describes a non-destructive mod to the light sensor that actually allows it to read ambient light! (URL) The range is <10 for a dark box and >90 for a halogen lamp about 6 feet away. It's really (...) (28 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Angle Sensor
|
|
Well, then I guess I need to build my own rotation sensor using a "Potmeter" (variable resistor) because I need a real angle, actually I need an angle per time value. Is this is possible? I saw something about this on a website in the mindstorms (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Angle Sensor
|
|
(...) Nope, wasn't me...I'll bet the fancy LEGO milling machine does something like it though... Maybe I should buy a rotation sennsor first :-) Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
One of the best suggestions (maybe from Ralph Hempel??) that I have seen for this sensor is to gear it up (down?) to get the desired rotational resolution. -Rob Doucette. Franz-Michael S. Mellbin wrote in message ... (...) (no. (...) 1 + (...) that (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
(...) The Lego rotation sensor counts each rotation in 16 steps starting from 1 (no. # 2 to 17 for the first full rotation). If the rotation goes backwards the count is negative (no. # 0 to -15 for the first full backward rotation). The count is (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Angle Sensor
|
|
Hi, Can someone tell me how the angle sensor works? Is it giving a RAW value back, or maybe even a real angle (between 0 and xxx, with step 1)? Where can I get the angle sensor in Europe (The Netherlands)? Thanks in advance... Michel -- Did you (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Good job, Ralph! The most compact solution seen up to now for a pneumatic switch. Mario (28 years ago, 27-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller (fwd)
|
|
----- Forwarded message from Ralph Hempel ----- Subject: RE: Why do it? Was: multi-device output controller (fwd) Date: Sat, 27 Mar 1999 02:17:09 GMT (...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller (fwd)
|
|
(...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write special software for the RS232 convertor's interface to the PC. Like I said, its cheaper and quicker to buy a second RCX from Pitsco... Cheers, Ralph (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|