To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4371 (+10)
  External Power Port Problem..?
 
Esteemed Colleagues, I have two RCXs, both of which have stopped responding to power applied to the external power port. With batteries, they function correctly; with a 9.6v Lithium Ion battery pack attached to the external port, nothing. This has (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  External Power Port Problem..? (fwd)
 
----- Forwarded message from Issac Merkle ----- From: "Issac Merkle" <the_gaff@hotmail.com> Subject: External Power Port Problem..? Date: Fri, 26 Mar 1999 06:08:01 PST I have two RCXs, both of which have stopped responding to power applied to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Why do it? Was: multi-device output controller
 
(...) I have checked this out, and if you use the standard RCX firmware (or other firmware that uses the RCX ROM, then you get the waveforms you are talking about at 125Hz 1/(1ms x 8). You also get polarity information - oh no, I've said too much. (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  RE: External Power Port Problem..?
 
(...) Ummm, It's not clear from your post, and I'm sure you have tried this, but have you tried a different adaptor? I tried to drive the RCX from a supposedly 9V wallwart, and it didn't work. The I used my lab power supply and started cranking it (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: Why do it? Was: multi-device output controller
 
Ralph, Thanks for reigning in the rabbit chase! As the originator of this thread I'd like to respond to the 'why'... I keep running out of ports on my creations. I see 5 or 6 as a practical limit. My criteria for a solution: 1. Entirely compliant (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  Re: Why do it? Was: multi-device output controller
 
I think that the solution should also be flexible enough to allow the power to be plugged into either an RCX output port or a battery pack. That way if you didn't want to lug around another battery pack, or if you didn't want to use up another (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: Why do it? Was: multi-device output controller
 
My original message described the controller with two inputs, one for device selection and one for device power. This could easily be connected to whatever power source the user desires. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Muscle wire and alternatives
 
I have connected nitinol to Lego and it can melt the ABS plastic...be careful. Rich (URL) Message----- From: Jim Choate [mailto:ravage@EINST...N.ssz.com] Sent: Friday, March 26, 1999 11:36 AM To: lego-robotics@crynwr.com Subject: Muscle wire and (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Why do it? Was: multi-device output controller
 
(...) Measuring PWM is not difficult, but it would involve a micro (PIC12C508 anyone?) dedicated to the task and then you would have to get it to drive the RCX, which means motor drivers, etc. If you are willing to spend $50 and LOTS of time, then (...) (28 years ago, 27-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  Why do it? Was: multi-device output controller (fwd)
 
----- Forwarded message from Ralph Hempel ----- From: "Ralph Hempel" <rhempel@bmts.com> Subject: Why do it? Was: multi-device output controller Date: Fri, 26 Mar 1999 22:17:57 GMT With all of the talk about RS232 converters, and PWM decoders, why (...) (28 years ago, 27-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR