 | | Re: multi-device output controller
|
|
Right. That is why you cannot use all 8 power levels. The polarity reversal that I am talking about is on the controlling (and only) output. I am already assuming, at this point, that drive power is stuck on as with your external battery box. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) Are you sure? I wasn't, so I went looking. The NQC docs seem to imply 7 powers levels plus off. Which, technically, is 8 levels of PWM, but if you use all of them, a motor is running at all times. That is fine if you use another motor output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
In my example the RCX output was just used to tell this mythical board which output to drive. Power for the output came from a battery box, always set to on. The RCX can't set direction on the battery box (at least not trivially). alex (...) -- Did (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Stepper motor design
|
|
----- Forwarded message from Wes Matchett ----- From: Wes Matchett <wes@augustschell.com> Subject: Re: multi-device output controller Date: Fri, 26 Mar 1999 17:34:25 GMT Now that I have brought up that topic, anyone know how to drive a stepper motor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
(...) [snip] (...) Dunno, I haven't looked yet, I just came up with the idea. (...) Because I felt like it? I've seen it written both ways. [snip] (...) Nope. 0 (speed) means off, no matter what direction you are going, therefore: 0= forward, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 12:33:18 -0500 OK now the details. 6. Send to a MAX232 devices and wallah, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Muscle wire and alternatives
|
|
----- Forwarded message from Joel Shafer ----- Date: Fri, 26 Mar 1999 11:12:57 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller (fwd) Has anyone tried out the Muscle Wire or electronic pistons from this site? (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
There is no need to waste PWM levels on reverse. You can set the RCX motor output to reverse speeds as well, giving you 7 outputs (fwd and rvs) instead of 3 1/2. You need a bridge rectifier anyway; you might as well exploit it to indicate direction. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) There are 8 levels of PWM, so fwd/rev for 4 devices is possible. I originally wanted a separate power input to allow a full 8 levels for each device. This would allow the controller to operate ANY device designed for the RCX ports and not (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
Cool. You can also add things like the following: 1. Serial LCD display 2. GPS devices 3. additional infrared send/recieve 4. ANY PC project that is serial port connected! I like the idea of multiple serial channels; this means that you can talk to (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|