To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4331 (+20)
  3-wire converter for homebrew sensors
 
Home-brew sensor fans - I have developed a converter brick to ease the job of attaching powered sensors to the RCX. The brick converts the RCX sensor interface to a standard three wire interface (+5, ground, and input voltage.) For more info go to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: lego turn table/list seems to hve slowed down
 
because robkc said, (...) for my digital camera (for panoramic shots) but have been having a hard time trying to get a stable base that rotates smoothly on a single shaft. I had to reply with: I used the same turntable for my digital cambot... Got (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Links on Mindstorms in Education
 
For those interested here is a list of links on Mindstorms in Education that I compiled from my bookmarks as a request. Links are in no special order and some sites (not links) are mentioned twice. I just checked the links, so they should all be (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) I wonder if you have looked at the simple method for connecting sensors to a RCX on my web page? It really only takes 6 diodes and a capacitor to create a powered sensor interface. Add a opamp if you need gain. This work was originally (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) [snip] (...) Ahh, but the stipulated purpose for Pete's sensor brick is that it gives a _linear_ response that isn't corrupted by the non-linear diode drop caused by currents that are often less than 2ma and perhaps not past the "knee" region (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Polarity Switch = Pressure Switch
 
Hi All, Just got my first Technic Polarity Switch and quickly put together a Pressure Switch for Pneumatics. Check out: (URL) and let me know what you think... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) It is a heck of a lot of complexity for a little added linearity. If you look at the plots on my general purpose interface section; the simple resistor interface is pretty linear. I think most of the nonlinearity in the powered version is due (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  multi-device output controller
 
I've been considering various ways to control more than three output devices with only the three ports and came up with the following idea. I don't have the electrical design knowledge to implement, so if this idea sounds good, I'd like to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
I have not tried pneumatics yet. I know where I will look when I try them out. This is another neat clean working device. Nice work! Bob Fay rfay@we.mediaone.net The Shop (URL) Hempel <rhempel@bmts.com> wrote in message (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
(...) Heck, I'd love to try some pneumatics, but you can't get a storage tank anywhere these days can you? All of the cool Technic kits are discontinued, no subs, (and while I'm whining) no shuttles, no tracked vehicles, only Throwbots and (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
(...) 8462 comes with two of them, and is available from Lego S@H. I'd like to see reissues of the construction vehicles as well. alex -- Did you check the web site first?: (URL) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
Dennis, Thanks for your encouragement. The angle sensor connected straight to the RCX is non-linear because it is in series with another resistor located inside the RCX. During a sense operation, the RCX drives the sensor input from a 10K resistor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) As for the diode vs FET, the package used for surface mount is going to be the same so there is no size penalty. The only thing I might change is the regulator, on battery powered equipment I would tend to a DC to DC converter like Motorola's (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
What about a real time circuit that routed the output power to one of eight output ports depending on the PWM. That way it only takes one output port on the RCX and up to three (out of 24) motors could be running at the same time. (...) like (...) (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Joel Shafer ----- Date: Thu, 25 Mar 1999 13:43:33 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller What about a real time circuit that routed the output power to one of eight output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors (fwd)
 
----- Forwarded message from Pete Sevcik ----- Date: Thu, 25 Mar 1999 21:00:13 -0600 From: Pete Sevcik <sevcik@flash.net> Subject: Re: 3-wire converter for homebrew sensors The angle sensor connected straight to the RCX is non-linear because it is (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
How well does this work? Contrast with: (URL) on (URL) I got from lu, and which seems to require a fair bit of fiddling to get it to regulate correctly. (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
 
  RE: Polarity Switch = Pressure Switch
 
(...) Mine required no tuning at all, if that's what you mean. I tried a similar configuration to lu's and found that the throw was difficult to get right. I don't like the overall size of my regulator, but it works like a champ! Cheers, Ralph (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
(...) [snip] (...) [snip] Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX can cycle the motors on and off, time it, and send a package a serial message at whatever the fastest BAUD rate is to control a max of N motors with (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Dennis Clark ----- From: "Dennis Clark" <dlc@verinet.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 15:27:53 GMT Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX (...) (28 years ago, 26-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR