 | | Re: Turrets for Robowars
|
|
Use the slip gear for the steering use a wheel based model. When steering hits limits clutch slips, Turret turns..then you just need a centering algortihm ro return turret and steering to center, or use same theory eccept that the oversteer (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Polaroid 6500 Sonar & LEGO
|
|
Two questions about the Polaroid 6500: Q1: Does anyone have NQC code to run this cool ranging system? If so, please share. Q2: Does anyone have suggestions about ways to mount the transducer (keeping it as much LEGO as possible)? All responses will (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Adder/Subtractor revisited
|
|
In article <36B6F795.4B9310A6@n...a.kth.se>, johannes@nada.kth.se says... (...) Ingenious as it is, this thread and previous similar ones have pointed out the primary problems with the A-S drive approach: power transmission through the LEGO (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Adder/Subtractor revisited
|
|
That sounds very interesting. I hope to see some diagrams or photos soon... Your approach solves the biggest problem introduced by the A-S drive, that of insufficient torque when driving tracks. Two motors is the way to go for tracks. -- SeeYa ! (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Adder/Subtractor revisited
|
|
In article <F6psw8.Bxy@lugnet.com>, cyberia@erols.com says... (...) Yes, this is the feature that really worked out well. By changing one gear (and adding appropriate number of 1/3 thickness shim plates under the motor), one can get the following (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Adder/Subtractor revisited
|
|
(...) Actually, I've had pretty good luck with independently driven left and right drive trains; I haven't had a lot of problems with robots curving when I want them to go straight. I find the adder/subtracter useful for a different reason: it makes (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: "synchro drive"
|
|
(...) Wish it was mine. :-) (...) I just used the 12T miter gears. 1:1 with the wheel offset equal to the wheel radius.I was just lucky that it fit the turntable so well. (...) I think the point of this platform is that it's handy to always have a (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Botcode/SetWatch
|
|
Chris Magno wrote in message <36BA8C67.5AC1BC47@myna.com>... (...) You can only use SetWatch with values not variables. It would be nice to have control of the display, but the standard code in the RCX doesn't allow it. (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor; 1999 Catalog
|
|
Issac Merkle wrote in message <19990205140702.9518...il.com>... (...) The internal counter is updated every 3ms. I'm sure the display isn't updated that fast so you won't see every angle on the display. I estimate the RCX can keep up with 1,000 RPM. (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Spirit + C++ Builder - help!
|
|
(...) I experienced the same problem. It seems to be related to the way C++ Builder handles the Pascal generated Spirit.ocx library, which I have seen suggested was compiled with Borland's Delphi :-/ The filename chosen by C++ builder for the .pas (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
|