 | | Re: Synchro drive in Lego
|
|
(...) Well I'd like to control the state of the motors independently so I'm thinking more of a demux (I just aquired 8 more motor kits that were being cleared from Target bringing my total to 10 geared motors and 2 of the older style 9V motors. But (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | WebSpirit
|
|
I am proud to announce, the release of WebSpirit, which enables you to control the RCX Via the ActiveX Control, and JavaScript, got check it out @ (URL) Ickna / Nick H. | (URL) Ickna@-nospam-aol.com | Remove -nospam- to send | You're not really (...) (28 years ago, 20-Jan-99, to lugnet.robotics, lugnet.general)
|
| |
 | | Basic to NQC
|
|
HI: :) I never thought people would take that last bit so seriously. I can live without line numbers. I had to learn to not use them after I got a basic stamp. pervious to that all my programing knowledge came from my glorified microcontroler (an (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | Help! Can't talk to IR Tower with Mac w/nqcc! [DAT]
|
|
I bought Mindstorms and downloaded nqcc to talk to the RCX, but I can't seem to get connected. I created a cable (actually its a bunch of cables strung together) and confirmed the wiring. I (ultimately) have the following: Mac IR (Male connector) 1 (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Help! Can't talk to IR Tower with Mac w/nqcc!
|
|
(...) I'm pretty sure that this only happens when the tower is properly communicating with the host PC (in this case, a Mac). At least, mine does, and it works fine. Perhaps you don't have the RCX powered on and in line of sight to the tower? I (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Help! Can't talk to IR Tower with Mac w/nqcc!
|
|
I thought so too. I did have the RCX on at the time. I also checked out the full communications tonight by downloading the firmware using Mindstorms. (A PC @ work is temporarily housing the sw!) so I know that everything else works. This is driving (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | RE: Storage Space
|
|
I bought a 42 drawer organizer from Home Depot. Normally used for small screws and stuff. The complete Mindstorms kits fits with some extra room to spare. -Kerry -----Original Message----- From: Clay Aucoin [mailto:caucoin@crui...oppes.com] Sent: (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | Direction of rotation sensor.
|
|
Hi, with no particular reason (YET) I'm trying to build a sensor that is able to find out the direction of rotation of a given shaft without adding significant load to it. It must use ONLY ONE touch sensor and ONLY RIS basic set parts. My initial (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | Re: ok, time for a stupid question...
|
|
I made my own version of these two designs that is, I think, stronger and cleaner. You can find pictures in the tips and tricks section on my lego web site. Mark Overmars (URL) > (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|
| |
 | | Re: is Mindstorm/RCX Y2K Compliant???
|
|
"....even when only relative time is required by the OEMs, this may often be derived from chips that keep absolute time internally. Those chips that represent absolute time using two digit dates are subject to Year-2000 failures just as with (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
|