To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 2986 (+10)
  Re: is Mindstorm/RCX Y2K Compliant???
 
(...) That's the same thing. Regardless of what exactly causes it, it'll happen. Jasper (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
=>From: rajackson@qnx.com =>... =>I've not tried this yet but... in the new geared motor sets there is =>a clutch plate with a Newton marking on the side. Also there is a =>ratchet design in the Cyber Wars kits. They use a shaft extender that (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  FW: rcxcc error
 
I hope this posts as I haven't had much luck in the past. Anyway - I am trying to run the RcxCC tools and I get the following error : Exception EOleSysError in module RCXCC.EXE at 00052F5D. Class not registered. Can anyone point me in the right (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  RE: rcxcc error
 
You must install the spirit.ocx. This is done either by installing the mindstorms software that came with the kit, or by locating the Spirit.ocx on the cd-rom, copy it to your system directory and run regserv32 on it 1. Run program (from the start (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  rcxcc problems
 
(...) Spirit.ocx on (...) I'm running Win95 - it doesn't have an executable named regserv32. I had previously installed the Mindstorms software, and the spirit.ocx file is present in the lego folder. I didn't see anything in either of the two readme (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  Fw: rcxcc problems
 
Isn't the Win9x version of that command regsvr32 ? I could have my OS wires crossed. trowt -----Original Message----- From: Mike Jones <MikeJ@scsitools.com> To: 'lego-robotics@crynwr.com' <lego-robotics@crynwr.com> Date: Tuesday, January 19, 1999 (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  Re: rcxcc problems
 
The REGSVR32.EXE tool can be found in the WINDOWS\SYSTEM or WINDOWS\SYSTEM32 directory, depending of the OS (Win95/NT). Laurentino Martins *<||:-) [mailto:lau@mail.telepac.pt] [(URL) you check the web site first?: (URL) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  Re: FLASHING LIGHT ON LCD PANEL?
 
In article <36A49D97.931256BD@myna.com>, Chris Magno <cmagno@myna.com> writes (...) Yes, me. If I spent less time reading lego-robotics and more time coding I would get there faster! I have written a qbasic program which will let you send bytecodes (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  RCX and h8hforth Forth programming language/firmware.
 
Has anyone else tried to upload the h8hforth.srec file into their RCX and successfully interfaced w/ the RCX via a generic COM program as described by Ralph Hempel? The Forth language/OS firmware is available at his website at: (URL) have not been (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  rcxcc problem - solved!
 
regsvr32 was the answer! Thanks loads! Sincerely, Michael Jones Peripheral Test Instruments, Inc. The Worlds Finest SCSI and FCAL Diagnostic Tools www.scsitools.com 303-763-7488 -- Did you check the web site first?: (URL) (28 years ago, 19-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR