To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 2781 (+10)
  Re: Do it yourself light sensors. How does RCX drive them?
 
(...) I end up with big blobs everywhere. Anyway, I fixed the drawing the way I'd do it and stuck it on my page. If you want, you can grab it from there and use it yourself. (URL) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: simple but functional radar
 
(...) I like it, our wheels stay on until it destroys itself by running full tilt into something black... Our design has two motors at the back driving wheels directly, and two free running castors at the sides as close to the front as possible, so (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: IR Port as night/day detector (Was: Re: IR Port as Proximity detector.)
 
(...) I though the RCX had a internal clock. I don't have a RCX so I can not tell. The CyberMaster doesn't. Laurentino Martins *<||:-) [mailto:lau@mail.telepac.pt] [(URL) you check the web site first?: (URL) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
(...) Well, apparently, neither can I. :) Or I would have done it and posted it. :) I played with some stuff last night that ended in a dead-end. I'm not really sure the approach is fruitless, but I'm realizing as I go on that I'm much less creative (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
(...) could you not (I haven't tried this!) use a ratchet on the assembly so that axle rotation one way turns the assembly, and the other way drives the wheel? Stuart -- Did you check the web site first?: (URL) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
(...) Yeah, but I can't think of a good way to ratchet the assembly. -Paul (pspeed@augustschell.com) (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Unidirectional gearing - was Synchro drive in Lego
 
Here's a really simple (but not fool-proof way): Feed the motor output into a differential gear. The output from the differentials run out through beams and have a medium gear just outside the beam. Then suspend another beam from one end using a (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in lego
 
(...) I've seen ratchets made with a pivoting gear rack element in contact with a 24 Tooth gear. Also, the small bungee racers had a ratchet mechanism also using several 16T gears. I'm quite curious to see what other variations of this platform (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in lego
 
Yeah, I've made these sorts of ratchets before. The problem isn't so much making a ratchet as it is ratcheting the wheel assembly to the platform. If I had one of those free-spinning dark grey gears I could do it. I may finally have to break down (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Pneumatic Tanks
 
Ian Sinclair wrote in message (...) That design was in response to a thread that was discounting pneumatics because their controls systems were "too big" and overall usefulness wasn't much. So I kinda wanted to undercut the complaint, since I like (...) (28 years ago, 14-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR