 | | Re: RCX and R/C combined
|
|
(...) snip (...) I'm only intending to use standard gear motors. Great answear Mark, that's exactly what I wanted to know. Steve (22 years ago, 9-Apr-05, to lugnet.robotics)
|
| |
 | | Re: My First MOC
|
|
(...) Rather than asking everyone to email you replies, you may want to look into subscribing to the group (perhaps temporarily) by email, via this URL: (URL) first doing this subscription setup: (URL) to get your confirmation code ) XFUT (...) (22 years ago, 9-Apr-05, to lugnet.robotics, lugnet.technic, lugnet.admin.general)
|
| |
 | | My First MOC
|
|
Pictures should be forthcoming in a few days of my first official MOC, the überCrawler. This is a 2 RCX, 6 motor beast that turns by raising itself via a two-motor winch. It has four independently-powered tracks, coupled into a front and rear pair (...) (22 years ago, 9-Apr-05, to lugnet.robotics, lugnet.technic)
|
| |
 | | Gearbox
|
|
Does anybody have diagrams, pictures, etc., regarding a "one-way" gearbox? This would have ideally one input and one output shaft, and the output shaft would turn the same direction no matter which direction the input was turned. Like a rectifier (...) (22 years ago, 9-Apr-05, to lugnet.robotics)
|
| |
 | | GPS Reality?
|
|
Is the idea of a GPS sensor compatible to the sensor ports an absurd idea? I have a few old Garmin units, with RS232 ports on them. I know of people who have incorporated these units successfully into "real" robots, but that usually involves heavy (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | Re: RCX and R/C combined
|
|
(...) Here's a diagram of the RCX sensor port circuit: (URL) Feeding a voltage of up to +9V (or the RCX battery voltage) will not harm the port, as this is what it uses in Active mode (light or rotation sensor). You can actually use an external 9V (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
|
| |
 | | RCX and R/C combined
|
|
I've just been experimenting with my RCX to see if it can sense the output from the Lego RC unit. The experiment was fairly successful, I was just wondering though if putting 9v into a sensor port does it any good. Are their any risks in making such (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
|
| |
 | | Re: Looking for the Mindstorms software.
|
|
(...) No it is not incorrect. You do have to install the USB tower drivers in order for NQC and BricxCC to use the USB tower to talk to the brick. That is not the case for the Serial tower. You can get the tower drivers (along with the firmware) by (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
here's some raw pix of one completed robot, another in construction, and an idea for a third, all using the omniwheels: www.danbmil.com/lego I'll try to clean up the pix, put some captions etc. later - dbm ps note that the additional duplo blocks (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
(...) Hi Dan, Maybe, could you provide some pixs of the heavy robot you built using the omni wheels. Thanks, Hakim (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
Wow, where did you find it? I will get four of these to me... Thanks "dan miller" <lego-robotics@crynwr.com> escreveu na mensagem news:20050407113954....hoo.com... (...) robots quite easily. You (...) tricky because the (...) lateral coasters is (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
you can use omniwheels, like the ones from Charmed Labs: (URL) only sell the single-row ones, but the double-row ones ((URL) can be adapted to Lego robots quite easily. You can also combine two single-row ones to work like a double, but it's a bit (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | unsubsribe
|
|
lego-robotics unsubscribe (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | Re: GBC module screw
|
|
(...) Ah, you have beaten me on the Archimede screw... I was thinking of this one, but I didn't get the screw right yet. Congratulations! Nice usage of micromotor. But it is slow, what is the ball throughput of your module? Any chance to look at a (...) (22 years ago, 7-Apr-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Land Walker
|
|
(...) Yes, it is. I would love to slide on down the street in that! (...) Kevin (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | Re: GBC 6 - the obsession continues...
|
|
I like the little agitator arm there - it took me a moment to see it - watching the vid. Nice module! I wander if we can bring it down to one motor, with some small transmition between the two.. Orion (22 years ago, 6-Apr-05, to lugnet.robotics)
|
| |
 | | Re: Land Walker
|
|
(...) True, although as a "slider" it seems to work pretty well. I'm assuming there are either wheels or some sort of treads in the feet. With the hips so wide, it appears to have a modicum of stability, although the movement does seem to make the (...) (22 years ago, 6-Apr-05, to lugnet.robotics)
|
| |
 | | Re: COMPLUBOT OnLine
|
|
Thank you very much. Your Web site is also a reference for us. Regards Eduardo ---...--- Original Message ---...--- From: "Claude Baumann" <cbaumann@ci.educ.lu> To: lego-robotics@crynwr.com Sent: Wed, 6 Apr 2005 18:25:50 GMT Subject: Re: COMPLUBOT (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
|
| |
 | | Re: GBC Current guidelines?
|
|
On Wed, April 6, 2005 2:18 pm, Frank Lee said: (...) Frank, Here's the standard that's used by most: (URL) if you need the French version :) (URL) the links to the video clips on the above pages ARE working, and there are also pictures here: (URL) (...) (22 years ago, 6-Apr-05, to lugnet.robotics)
|
| |
 | | Re: Land Walker
|
|
(...) I wondered about this, its stance did not appear to lend itself to walking, with the hips so far apart, and the feet so far apart. Kevin (...) (22 years ago, 6-Apr-05, to lugnet.robotics)
|