 | | Re: The Great Ball Contraption
|
|
(...) Yep. The IN basket is really more of a "target zone" - the upstream module should drop the balls into your IN basket zone (really, the 8x8 center section) from a height of at least 10 bricks (no specified upper limit, so when building your (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Really, the only thing defining a "module space" is a flat L & R edge, and no part of the module extending more than 32 studs from the front edge of the input bin "zone" - the footprint need not be remotely rectangular, nor is there a set (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Sure enough, that'll happen. What about the sawdust envy that LEGO soccer balls will inevitably suffer from? Ed (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Or someone who owns a soccer ball could measure it and publish the size. Most craft stores sell a selection of little wooden balls. It might be cheaper to buy a few about the right size rather than paying to mail genuine Lego ones? Of course, (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Cool - That works for me :) Steve - on the page it says "The IN basket should be 10 studs by 10 studs (outside dimension) with an 8x8 opening, and should be 10 bricks (beams) tall." and "Each module should be able to accept balls at an average (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I read that, I just decided to be a little more apparent, as in 'Gee Steve, send me some balls!' ;) I have a grande total of, wait for it... 1 soccer ball, and it came with my Brickfest '04 set. At your convenience, of course :) Dave K (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) To clarify--are we allowed to use 2 'module spaces' if we want? As well, I notice that the train ran along 'outside' the designated module area--is that allowed as well? Do we then have to get permission from our neighbouring module owners to (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Hidden somewhere on the page above, it says I can suppily you with soccer balls. Thanks to Christina, I have exactly enough to suppily EVERYONE with soccer balls. If I run short, I'll just talk with Larry... :) And, for the record, the you are (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) This is fantastic. The movie is well worth the download, because if the words don't encourage, the pictures certainly will. If enough people sign up, we'll need a seperate GBC room :) JB (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Oh My Goodness!!! I'm so there for this!!! This looks like the funnest thing to happen to RCX's since rtl events. Where does one purchase 20-30 soccer balls? Dave K (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | The Great Ball Contraption
|
|
In an attempt to provide Technic & Mindstorms builders the same cooperative building opportunity that's available to Moonbase, Castle, and Town/Train builders at Brickfest, we present to you: The Great Ball Contraption. When it's assembled at (...) (22 years ago, 7-Jan-05, to lugnet.robotics, lugnet.technic, lugnet.trains, lugnet.events.brickfest, lugnet.events, lugnet.announce) !!
|
| |
 | | Re: RCX Sensor Port
|
|
(...) Experiments completely second that, see this V/I curve I measured while preparing my (URL) GP2D12 interface>. Philo (URL) (22 years ago, 7-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | RCX Sensor Port
|
|
I've been looking into the interface of the RCX sensor port, as well as studying available information. This page from Stef Mientki suggests that the port uses a current source: (URL) believe this to be correct. According to the circuit topology and (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
|
| |
 | | Re: Uses for tacho wheel?
|
|
(...) Whilst white tacho wheels were used by the barcode truck for speed sensing (on the truck for variable engine rev sounds), the Star Wars UCS X-Wing used grey ones on the cannons(?) on the wings. Tacho wheels have 8 slots that will hold flex (...) (22 years ago, 6-Jan-05, to lugnet.robotics)
|
| |
 | | Re: Uses for tacho wheel?
|
|
(...) They were used to interupt the light beam/sensor on the Code Pilot allowing the Code Pilot to sense shaft rotation. -Rob. (22 years ago, 5-Jan-05, to lugnet.robotics)
|
| |
 | | RE: Uses for tacho wheel?
|
|
If you point a light sensor at them, you can use them as a rotation sensor. They are also available in one of the NBA basketball sets. If memory serves, they used it as a gear that was part of a ratchet mechanism to keep the wind-up motor from (...) (22 years ago, 5-Jan-05, to lugnet.robotics)
|
| |
 | | Uses for tacho wheel?
|
|
Attempt #2 at this post... I recently aquired (via the "grab bags" at LEGO stores - wonderful idea, second only to PaB for me) two of the "tacho wheels": (URL) played with them only a little, but how do you *use* these things? I'd download the (...) (22 years ago, 5-Jan-05, to lugnet.robotics)
|
| |
 | | Re: RCX IR Transceiver and Sensor Port Circuits
|
|
(...) Here's the (hopefully) finished circuit diagram for the IR Transceiver, complete with semiconductor component types and bold lines. I changed the supply rail voltage to concide with the zener diode voltage. There's also a space on the board (...) (22 years ago, 4-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | out
|
|
Please put me out of the adress list. I don't want to receave any post any more. Tanks (22 years ago, 3-Jan-05, to lugnet.robotics)
|
| |
 | | Re: 2-wheelers
|
|
I've been looking at that little piece of code, and trying to duplicate its effect in my YAL-based program, without much luck. When I had Steve's code running, it did tend to stay in one spot, but it eventually became unstable. At this point I plan (...) (22 years ago, 2-Jan-05, to lugnet.robotics)
|