 | | Re: challenge: LEGO copier
|
|
(...) OK, just to clarify: assume an X-Y-Z space with studs sticking up in the Z direction. You mean a model that's only one stud thick in X, arbitrarily wide in Y, and arbitrarily high in Z? Yes, that would be a much simpler problem than what I was (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) The closest I got to something like that was my half-built Duck Assembly Carousel - a dial automation with 4 positions, which would assemble the body (2x1 inverted slope), beak (2x1 plate), and head (1x1 brick with a hole in it). I didn't have (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
Would the bricks be assembled as a wall one brick thick on its side? Like laying a cinderblock wall on its side then creating a copy? That might be done with an X-Y table arrangement with vice like sides at top and bottom of the bricks so that they (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) There are some clever tricks (diff & ratchet/clutch, muxes) to expand it somewhat for some applications, but in general, yes, a single RCX can drive only three independent pulse-width modulated polarity reversible 9V outputs. -SMQ Shawn (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) No, I meant stuck to each other. (...) That's what I had in mind too. (...) I was assuming the use of a camera, not the LEGO light sensor. But using the light sensor is a clever idea. (...) Here I expose my complete cluelessness with regard to (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) I wasn't thinking that the bot would have to exactly reproduce which same-color bricks are used side-by-side -- if I used a two 1x2 bricks, but the robot chooses to substitute a 1x4 brick, in my mind that's the same model. We'll just say the (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Actually, he said "flat". So I would assume that he meant an assortment of bricks simply stuck to one baseplate, sort of like a mosaic. As for brick boundaries... I think the only thing you would need to worry about is the boundaries where the (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Here's an easy 'rule' you could add to resolve that. Just say that a given color may only be used for one size/type of piece. You don't even have to specify what colors are used, as long as any color may only represent one piece type. To make (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Ugh. Much harder than it sounds: either the robot needs extreme visual acuity to spot the brick boundaries (so it can tell two 1x2 bricks of the same color end-to-end from a single 1x4 brick... or, more importantly, which order a 1x1 and a 1x4 (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | challenge: LEGO copier
|
|
Here's an idea I am certainly not equipped to attempt, but I bet somebody is... The user builds some model (constraints: it must be composed of a 1x1, 1x2, and 1x4 bricks in a selection of several colors, and must be flat, i.e. two-dimensional, and (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|