To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22619 (-10)
  Re: challenge: LEGO copier
 
(...) I wasn't thinking that the bot would have to exactly reproduce which same-color bricks are used side-by-side -- if I used a two 1x2 bricks, but the robot chooses to substitute a 1x4 brick, in my mind that's the same model. We'll just say the (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Actually, he said "flat". So I would assume that he meant an assortment of bricks simply stuck to one baseplate, sort of like a mosaic. As for brick boundaries... I think the only thing you would need to worry about is the boundaries where the (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Here's an easy 'rule' you could add to resolve that. Just say that a given color may only be used for one size/type of piece. You don't even have to specify what colors are used, as long as any color may only represent one piece type. To make (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Ugh. Much harder than it sounds: either the robot needs extreme visual acuity to spot the brick boundaries (so it can tell two 1x2 bricks of the same color end-to-end from a single 1x4 brick... or, more importantly, which order a 1x1 and a 1x4 (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  challenge: LEGO copier
 
Here's an idea I am certainly not equipped to attempt, but I bet somebody is... The user builds some model (constraints: it must be composed of a 1x1, 1x2, and 1x4 bricks in a selection of several colors, and must be flat, i.e. two-dimensional, and (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
(...) Take two valves, two 2cm tubes with an antenna stuck in the end, a 8cm tube and input and output tubes. Arrange the valves so that they switch together, using "1" joints on their levers, connected by a liftarm (centres 32mm apart for old (...) (22 years ago, 2-Aug-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
(...) I'm not clear on this. It sounds interesting, I just can't picture how it's done. Where does the tube go? Is it acting like a little variable volume reservoir? (...) I agree completely here. Hydraulics would be *much* more complicated, (...) (22 years ago, 2-Aug-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
Thank you much! (22 years ago, 27-Jul-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
(...) One way to change pressure in Lego pneumatics by a small amount is to switch in a short tube (2cm) with an antenna stuck in the end. This lets only a small amount of air out of the cylinder, whilst not exhausting any to the atmosphere. (...) I (...) (22 years ago, 31-Jul-04, to lugnet.robotics)
 
  Re: USB Tower
 
Hi Alberto, (...) yes, and I take care of the driver as of 2.6.6 . You really don't need the LEGO Software. (If you just want the driver you can get the RCX SDK 2.5.) Jürgen (22 years ago, 30-Jul-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR