To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22579 (-20)
  Re: Power saving on L293D???
 
(...) Looking in an old Maplin catalogue from 1998, the entry for the L293D shows a total quiescent logic supply current of 16mA per chip, so 48mA total. Presumably you're using a 9V logic supply to match the RCX outputs? The output supply current (...) (22 years ago, 6-Jul-04, to lugnet.robotics)
 
  Power saving on L293D???
 
Hi, I'm building my own controller to use with Mindstorms. I want to support 6 motors, with 3 L293D IC's. But I found that this IC needs about 25 - 30 mA on the logic supply, when the chip is disabled. That means even if I dont use any motors the (...) (22 years ago, 6-Jul-04, to lugnet.robotics)
 
  Re: RCX firmware vs hardware
 
(...) No, that won't cause any problems. The software versions are all interchangable between the RCXs, so you can use 1.0, 1.5 or 2.0 software/firmware on 1.0, 1.5 or 2.0 RCXs. I have both 1.0 and 2.0 RCXs, and I use the same firmware on both. (...) (22 years ago, 6-Jul-04, to lugnet.robotics)
 
  RCX firmware vs hardware
 
All, I've got an RCX 1.0, and my son has a 1.5. Is there anything that would cause problems if I loaded 1.5 firmware into a 1.0 RCX? While on the topic, what about 2.0 firmware in a 1.0 RCX? (22 years ago, 6-Jul-04, to lugnet.robotics)
 
  Re: Repairing small 9v battery box
 
(...) Hmmm, difficult. After a quick inspection, I'd say no. (...) What batteries are you using? I doubt there's many 9V batteries that can take sustained 5A for very long. ROSCO (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: Repairing small 9v battery box
 
(...) I had a large battery box that was did not work reliably (sometimes yes, sometimes no). The problem was burning at a battery contact. The current does not need to be very high to do that if the contact area is very small. The discolored spots (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Repairing small 9v battery box
 
I've got one recently off od Bricklink, and it seems not to be working. Yes, new battery, yes, battery works in other small 9v boxes, yes, I made sure it was cool (thermal protection). Any ideas? Any suggestions how to troubleshoot or fix it, (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) Steve, no doubt you' re the best !! ;-) quite simple !! perfect!! the good thing is that it works even when program runs.... Thanks a lot (hey Steve have you the seen the gyro-bob on my site, the simplest mechanical alternative to legway: (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) don't give up. without any programming, the remote will drive the spybot. button 1 & 4 control the right motor, button 3 & 5 control the left motor. It seems messed up, but that's how it is. If the motors go the wrong way, you can switch the (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) front,button 3: right) and it looks too hard for me... do I have gave to give up ? :-) thanks Chris. (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
This is not exactly what you are looking for, but I hope it helps! (URL) think you can use the same process, but you will have to learn what code each button on the remote sends. (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) Hi Steve :-) OK, does it means "spybot" listen remote as it was another spybot ?? using exactly same communication functions ? how can you change remote ID ?? do you have a link where I can find further informations about spy communications?? (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) it's sending (1,2, or 3). All the programming is in the Spybot, where you can change how it responds to different buttons. Steve (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  how to program the spybot remote
 
hi everybody ;-) I use brickCC to program my spybot, do you know how I can program remote' s functions ?? (I talk about the spybot's remote) I' m not a programmer specialist so could you give me few code or a good explanation Thanks to all Chris (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) Instructions for building a diode-based limit switch can be found at (URL) also has a limit switch adapter, that lets you use standard Lego switch sensors to stop a motor without using any sensor ports. (22 years ago, 1-Jul-04, to lugnet.robotics)
 
  Re: Ultimate ROBOLAB
 
(...) Thanks Jerry, In fact Ultimate ROBOLAB programs are "firmwares". You can design simple programs or even complex ones controlling advanced robots. You also can use the software to write a complete firmware as a state machine controlling the RCX (...) (22 years ago, 28-Jun-04, to lugnet.robotics)
 
  Re: BrickFest is coming, and so are the robots!
 
(...) The reason behind that is pretty simple. It's because I've entered many of the challenges. I've seen what other people out there can do, and I'm just lucky they haven't been entering. I was just looking over the rules, and (as usual) John's (...) (22 years ago, 28-Jun-04, to lugnet.events.brickfest, lugnet.technic, lugnet.robotics)
 
  Re: Ultimate ROBOLAB
 
(...) exciting, but I am a bit confused about what it is. It's a programming tool (piece of software) that creates 'assembler programs' which are downloaded to the RCX in the same way as you download firmware. Each one allows the RCX to be used to (...) (22 years ago, 26-Jun-04, to lugnet.robotics)
 
  Ultimate ROBOLAB
 
Have a sneak preview of this ROBOLAB based development environment to create RCX firmwares: (URL) (22 years ago, 26-Jun-04, to lugnet.robotics)
 
  Re: Robolab Conference
 
(...) Great occasion to meet enthousiasts, specialists and even authors of ROBOLAB. Chance to learn more about this widespread software. Challenge to hear about Ultimate ROBOLAB, a graphical tool to write RCX firmwares. See you there Claude Baumann (22 years ago, 26-Jun-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR