 | | RE: is it possible to make a motor with a limited range of travel?
|
|
(...) belt. (...) Hello, If you take a beam and put racks on it, you can push that across a gear and it will make the gear spin. A back and forth motion causes back and forth rotation on the gear. To get mechanical back and forth motion, simply (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) There are some methods involving non-lego peices in the mix. One such method, is to build a touch sensor using a microswitch from a mouse. Wire this in the normally closed way - so when it is activated, it will open. So the motor will go the (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Or you may use poor man's clutch gear: pulleys and slipping rubber belt. Or if your application does not need too much mechanical power, you can simply use a low power level on RCX output. With a power level 2 both the RCX and the motor can (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) clutch (...) at (...) You should only need one touch sensor per rack. If you only have one motor per rack, then you should be able to use one sensor per motor (unless you have other stuff you need the sensor ports for, of course). M RRR...RRR (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Thats kinda usefull except that I dont have enough clutch gears, touch sensors or sensor inputs on my RCX :( (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
Jonathan, What about putting stops on the rack to limit the travel and use a clutch gear to keep the motor from being damaged? Or what about putting a peg at each end of the rack that stick out and hit a touch sensor when the gear rack is close to (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | is it possible to make a motor with a limited range of travel?
|
|
Basicly, I want a setup where a motor has a gear wheel connected to a long gear rack. Then I want to have things so that holding down the motor buttons (up and down) will move the rack but wont allow it to move off the end of the rack. Anyone got (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) Gabe, Did you see my other post in this thread? (URL) includes a link to the VLL data format. Using that, it shouldn't be hard to build something that can "talk" VLL to a Spybot. You'd be able to send messages (a number from 1 to 127) from the (...) (22 years ago, 16-Jun-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) So, for instance, if I want to use a spybot to control something else, what VLL codes I can to use? Can it also get info back from the other controller? Can VLL be used to make the spybot talk to some other microcontroller like OOPIC or (...) (22 years ago, 16-Jun-04, to lugnet.robotics)
|
| |
 | | New RCX alternative ?
|
|
Hi,All I just got this in my email. It appears that there is a new, more powerful alternative to the RCX available : ) Check out the XRC here : (URL) not affiliated with Charmed Labs in any way, other than being a happy customer. I had purchased an (...) (22 years ago, 14-Jun-04, to lugnet.robotics)
|