To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22549 (-10)
  Re: is it possible to make a motor with a limited range of travel?
 
Jonathan, What about putting stops on the rack to limit the travel and use a clutch gear to keep the motor from being damaged? Or what about putting a peg at each end of the rack that stick out and hit a touch sensor when the gear rack is close to (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  is it possible to make a motor with a limited range of travel?
 
Basicly, I want a setup where a motor has a gear wheel connected to a long gear rack. Then I want to have things so that holding down the motor buttons (up and down) will move the rack but wont allow it to move off the end of the rack. Anyone got (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: RCX and Micro Scout Communication
 
(...) Gabe, Did you see my other post in this thread? (URL) includes a link to the VLL data format. Using that, it shouldn't be hard to build something that can "talk" VLL to a Spybot. You'd be able to send messages (a number from 1 to 127) from the (...) (22 years ago, 16-Jun-04, to lugnet.robotics)
 
  Re: RCX and Micro Scout Communication
 
(...) So, for instance, if I want to use a spybot to control something else, what VLL codes I can to use? Can it also get info back from the other controller? Can VLL be used to make the spybot talk to some other microcontroller like OOPIC or (...) (22 years ago, 16-Jun-04, to lugnet.robotics)
 
  New RCX alternative ?
 
Hi,All I just got this in my email. It appears that there is a new, more powerful alternative to the RCX available : ) Check out the XRC here : (URL) not affiliated with Charmed Labs in any way, other than being a happy customer. I had purchased an (...) (22 years ago, 14-Jun-04, to lugnet.robotics)
 
  My new website (with some MOC´s)
 
Hi everyone! I want to anounce my new site dedicated to LEGO! Currently, it have only 3 MOC´s, but I hope to make it bigger with the time... I´m also anouncing my new robotic car - with rack-and-pinion steering and rear suspension. You can see the (...) (22 years ago, 13-Jun-04, to lugnet.technic, lugnet.robotics)
 
  Re: Favorite robot ?
 
(...) lugnet.. I started building J5 about a year ago. Since then I I built on im my rare freetime (family an my on company are taken my time away..) On BrickShelf I'm posting some pictures from time to time. J5 isn't finished jet. I think, I will (...) (22 years ago, 11-Jun-04, to lugnet.robotics)
 
  P'titgneugneu the stairs climber, was Re: CC3:Stairs,
 
Here is the (URL) write-up> about the robot I built for CC3:Stairs contest, that happened to win ;o) A bit flimsy, not too pretty, but it did the job! (URL) As the results have not been published here, I inserted the official announcement below. (...) (22 years ago, 10-Jun-04, to lugnet.events, lugnet.robotics, lugnet.technic, lugnet.announce, FTX)
 
  Re: VLL Codes
 
(...) If you want to print out all the codes on one piece of letter sized paper, I have modified the file from (URL) to do so for the Codepilot. It is here (URL) in both Postscript and PDF format. (...) (22 years ago, 7-Jun-04, to lugnet.robotics)
 
  Re: Motor-powered transmission
 
(...) I just built that, but using the instructions, the 20t bevel gear used for 1st gear scrapes one of the 1x8 plates. Moving the plates up to the top solves the problem (I also used 2x8s to help keep it square). HTH ROSCO (22 years ago, 7-Jun-04, to lugnet.robotics, lugnet.technic)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR