 | | Re: Ultrasonic sensors - comparison & performance?
|
|
Has anyone pulled the ultrasonics from a Nintendo Powerglove yet? I saw someone using bend sensors wit the RCX, but haven't seen anything on the ultrasonics. The glove comes with two transmitters and three receivers and was originally used to (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: LejWay (Re: Legway with Standard Lego Light Sensors)
|
|
Hi Philippe, (...) nice to hear, for me it didn't work any more when it was darker. I would like to have some automatic calibration of the parameters to be more robust w.r.t. conditions, but I guess that is difficult. (...) Yes, probably one could (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Ultrasonic sensors - comparison & performance?
|
|
(...) Most of my results from the HiTechnic sensor were the opposite of this. I find it to be very useful, so I use it all the time. The readings seem to show a good, linear output based on the distance. (even though I usually use it as a binary (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Ultrasonic sensors - comparison & performance?
|
|
Hi, I own the 24Khz from Mindsensors. I have not played with it a lot, mainly because I cannot get useful behavoiur. The device works nearly as a binary detector, object present in xxx meter or no object. Minimum distance is around 30 and max about (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Ultrasonic sensors - comparison & performance?
|
|
(...) I have no personla experiance of any ultrasonic range sensors (still waiting for my sensor from HiTechnic). But I found this extensive test of the HiTechic sensor. (URL) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Ultrasonic sensors - comparison & performance?
|
|
(...) I cannot provide any comparison information because I think it would be improper of me to do so. I would like to set out a couple of technical details relating to distance measurement using ultrasonic techniques, since I have been involved in (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: The grand challenge
|
|
(...) (URL) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Re: The grand challenge
|
|
Where can I find more information about this challenge? thanks Scott ----- Original Message ----- From: "Ian Smith" <ian@astounding.org.uk> To: <lego-robotics@crynwr.com> Sent: Tuesday, March 16, 2004 2:59 PM Subject: Re: The grand challenge (...) (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Ultrasonic sensors - comparison & performance?
|
|
I've been looking at ultrasonic sensors for the RCX - two seem currently availible, the 24 kHz one from Mindsensors, and the 40 kHz one from HiTechnic. What experience do people have with these, specificly? I suspect they wouldn't interfere with (...) (23 years ago, 18-Mar-04, to lugnet.robotics)
|
| |
 | | Mindsorms related resources
|
|
Robofesta-UK is an open educational robotics network established in 2000 to promote science, engineering, technology and maths education through hands-on robotics activities. We have recently relaunched the RoboFesta-UK website (...) (23 years ago, 17-Mar-04, to lugnet.robotics)
|
| |
 | | Re: LejWay (Re: Legway with Standard Lego Light Sensors)
|
|
Bonjour Jürgen, (...) I just tried LejWay, it works fine! (it was also the opportunity to install Lejos under BricxCC. Works great too...). The behaviour is somewhat different from BrickOS version, less shaky but it falls if tilt angle is too high. (...) (23 years ago, 17-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Some brainstorming needed.
|
|
(...) The device you describe above is a 3D printer from Z-Corp. (URL) had the pleasure of using one, on loan from Z-Corp for a month. It is a wonderful prototyping device, although SLA (stereolithography) prototyping systems produce superior models (...) (23 years ago, 17-Mar-04, to lugnet.robotics)
|
| |
 | | LejWay (Re: Legway with Standard Lego Light Sensors)
|
|
Salut Philippe, hi everybody, (...) a Lejos version. The hardware is the same with two sensors, and the program is loosely based on yours. Tweaking was not easy, but with a little luck the program below now manages to stand on a sheet of white paper (...) (23 years ago, 17-Mar-04, to lugnet.robotics, lugnet.robotics.rcx.java)
|
| |
 | | Re: Legway with Standr5ad Lego Light Sensors
|
|
(...) Hi Barry, Have a look to YAL... (URL) (23 years ago, 17-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Legway with Standr5ad Lego Light Sensors
|
|
(...) I recall someone put a pair of light sensors out on the end of very long arms out in front and back of the robot. This meant that they moved a much larger distance than if they were mounted close to the wheels so that their relative lack of (...) (23 years ago, 16-Mar-04, to lugnet.robotics)
|
| |
 | | Legway with Standr5ad Lego Light Sensors
|
|
Hi: I am sorry if this is a repeat question. Did anyone successfully stabilize the Legway using standard Lego light sensors ? Any links or proofs, code, etc ? Thanks Barry (23 years ago, 16-Mar-04, to lugnet.robotics)
|
| |
 | | Re: The grand challenge
|
|
(...) According to the map of track-logs I saw, a few appeared to end further from teh finish than they started. regards, Ian SMith (23 years ago, 16-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Some brainstorming needed.
|
|
what about putting the Dremel tool at the end of a lego motor ? To cut thin Balsa, it should be strong enough. If the Dremel power is necessary, then you can have it fixed upwards on a table, and have the lego plotter to move the Balsa plate onto (...) (23 years ago, 16-Mar-04, to lugnet.robotics)
|
| |
 | | Re: Brute Force Brick
|
|
(...) Well, think about a top of the table fixed industrial machine, instead of a bot moving around. LEGO technics offers great possibilities to build such a prototype. I have two incredible machines in mind: The first one is a sorter for electronic (...) (23 years ago, 16-Mar-04, to lugnet.robotics)
|
| |
 | | Remove from maillist
|
|
please remove me from your mailing list. Thanks! (23 years ago, 15-Mar-04, to lugnet.robotics)
|