To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 221 (+10)
  Re: Dacta angle sensor
 
(...) I missed something. Where did you get this piece from again? -Kekoa (28 years ago, 27-Oct-98, to lugnet.robotics)
 
  Re: Dacta angle sensor
 
(...) It came with a bunch of Technic stuff I acquired, including a lot of 4.5V stuff. Came from a school in England, I got everything they had :-) Matt (28 years ago, 27-Oct-98, to lugnet.robotics)
 
  Messaging between Cybermaster and Mindstorms
 
Mindstorms and Cybermaster can't send each other direct messages because of the different physical transmission techniques (infrared vs radio waves). Therefore I added a control panel to Mind Control, which allows the two units to exchange messages (...) (28 years ago, 28-Oct-98, to lugnet.robotics)
 
  CYBERMASTERS - how it works ?
 
Heya all ! I wanna buy Cybermasters set. But I want to know HOW it works. Must I program this "programable brick" before and then it makes this PROGRAMED motions or can I control this model interactive for example by joystick or mouse ? Like radio (...) (28 years ago, 28-Oct-98, to lugnet.robotics)
 
  Controling LEGO trains via Decta Control Lab
 
Hi All, I have been working on controlling LEGO trains thru the Decta Control Lab and I got a tip to pulse the power to the rails to better control the trains speed. There are 8 power settings via the ctrl lab and there are really only 2 or 3 (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
 
  Mindstorms A/D, 8 bit or 10 ?
 
OK, I just got a Mindstorms this yesterday and I've been surfing the various web pages about it (Lots of good info!) and I came across something odd. The specs for the microprocessor say it has 8 bit A/D's (Analog to digital converters), but the raw (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
 
  Re: Controling LEGO trains via Decta Control Lab
 
(...) To change the speed of the pulsing, you change the frequency. Frequency is measured in Hz. You want more Hz. To change the speed of the train, you increase either the duty cycle or the voltage. The duty cycle is the percentage of time that the (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
 
  Re: CYBERMASTERS - how it works ?
 
Rene Virsik wrote in message ... (...) program (...) can (...) radio (...) Both. Pplease read yor answer in here. Eric (28 years ago, 29-Oct-98, to lugnet.robotics)
 
  Re: Controling LEGO trains via Decta Control Lab
 
10Hz is nowhere near fast enough to control a train motor using PWM (pulse width modulation). You need at least 100Hz, and higher would be better. Any of your suggestions will vary the speed of a motor, but the most common is varying the duty cycle. (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
 
  Re: Controling LEGO trains via Decta Control Lab
 
I was hoping someone would post a solution to the software platform. I would even kill for just the low level API to the control lab direct and write my own Visual Basic OCX for it. The LOGO development environment is a bit forgien to me and is (...) (28 years ago, 29-Oct-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR