 | | Chat server is up! (was: Need for chat server?)
|
|
Hello all, I finally found a free moment to set up the chat server for all of us lego and robotics maniacs. My company is going through a merger with another .com so things are a bit busy right now ... I haven't had much time to mess with my lego (...) (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: Length of Diagonal Spreadsheet
|
|
(...) Yes - I have such a table too - but I generated it with a program that automatically rejects unusable combinations to generate a small list of useful diagonals. (...) Ah! That makes more sense. So you mean errors of 0.05 studs - that's a bit (...) (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: Length of Diagonal Spreadsheet (Now in PDF format!)
|
|
Thank you everyone who either offered to make a PDF file or went ahead and made one and mailed it to me. Here is the PDF version of the spreadsheet. (URL) suggest that you print it out and try out some of the diagonals. For the new 12 and 20 tooth (...) (24 years ago, 8-Apr-01, to lugnet.org.us.smart, lugnet.robotics, lugnet.technic)
|
| |
| | Re: Length of Diagonal Spreadsheet
|
|
(...) Thanks for the link to your gear spacing site. That is sort of what I was looking for though in my chart I aimed at being more general then just a list of workable gear spacing. My diagonal measurements can also be used to find workable beam (...) (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: Length of Diagonal Spreadsheet
|
|
(...) ---...--- snip ---...--- (...) Gus I can't download the sheet nor can I open it online. If you can email it to me I can convert and return the pdf via email, providing the document isn't too large for your mail box. Dave (24 years ago, 7-Apr-01, to lugnet.robotics)
|
| |
| | Re: A couple of questions
|
|
(...) Only by the vocal majority, I think. There has been a recent thread about a sub-group (cult?) of "grinders". I say the end justifies the means here. You might look into FischerTechnik (my spelling may be off). Someone on this newsgroup did (...) (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: Length of Diagonal Spreadsheet
|
|
(...) Er oops :) that's a 2L spacing, same as 24T to 8T or 16T to 16T. (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: Length of Diagonal Spreadsheet
|
|
(...) I'm assuming he's talking about the 12T double bevel gear. Three sets that I know of that have them are the DDK, the Technic 8448 Super Street Sensation and the Technic 8008 Stormtrooper. They have a standard 3L mesh spacing when used with a (...) (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: Length of Diagonal Spreadsheet
|
|
(...) For gear spacings, you might try: (URL) My testing shows that errors as great as 5% are usually no problem for (...) That *can't* be right. The tolerable error for two 40t gears is no different from the error for two 8t gears - so it's (...) (24 years ago, 8-Apr-01, to lugnet.robotics)
|
| |
| | Re: program wont stop running
|
|
(...) If the person stops running, then that means the program has stopped. The "Run" button stops a program and turns off the motors. However, when a program finished normally (with nothing more to do), the motors are left in whatever state the (...) (24 years ago, 8-Apr-01, to lugnet.robotics, lugnet.robotics.rcx.nqc)
|
