 | | (no subject)
|
|
(...) Some time ago I did come across a site that talked about hacking a sonar tape measure. I can't remember where I saw it but I am confident that I had encountered it by searching "sonar" on one of the major search engines. You could be more (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid sonar problems
|
|
hi! Our group is still struggling with the polaroid sonar. We can't get any coherent reading, only readings that are in the range 470-515, which aren't effected by the measured distance. We have the capacitor and resistor installed as required. We (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Problem with VB an cybermaster
|
|
Stefan Prescher wrote in message ... (...) brick (...) You left out the opening ceremonies. See (URL) Brok (28 years ago, 1-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Might be new to Mindstorms
|
|
Mookie wrote in message <36D831C7.78D50CF5@e...pc.com>... (...) Both RIS and Cybermaster are much more versatile than RC and Barcode Pilot. The RC car isn't good for anything else but RC controlling a car and even limited in that too (no variable (...) (28 years ago, 1-Mar-99, to lugnet.robotics)
|
| |
 | | Wheel encoders
|
|
(...) Yes, the pulley wheels near the drive wheels were drilled to accomodate 0.1" dia. disk magnets, available at the local hobby shop. The magnets activate the Hall effect magnetic sensors that are tucked away into the chassis (not easily seen in (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Working with Legos
|
|
Servo Tape: Available at R/C suppliers, this is sheet rubber with very strong stickum on both sides. The only problem is that it will creep, so if the part will be under stress you should augment servo tape with either Ty-Raps or a fillet of (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mindstorm hacking program
|
|
I heard that someone at MIT created a program that can hack into and advance Lego mindstorm's computer. Does anyone know where i can find this site where i can download the program? =) chen (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | serial communications
|
|
I want to disconnect interactive C from the handy board and send instructions to it via the hyper terminal on Windows 95. I have followed the instructions given in the HB technical reference. I am confused as to the procedure for accomplishing my (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: serial communications
|
|
some days ago i played with this too. i send you my files ... hope it helps ;) /* beginning of serial.c */ int char1; void disable_pcode_serial() /* necessary to receive characters using serial_getchar */ { poke(0x3c, 1); } void (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Inchworm
|
|
Pointless Invention Of The Week: I've put together a Lego "inchworm" using the MindStorms RIS and a few more pieces. Utterly silly, good for a chuckle or two. Pictures at: (URL) has no sensors, and it uses the RCX as nothing but a dumb battery box. (...) (28 years ago, 1-Mar-99, to lugnet.robotics)
|
| |
 | | Bipolar Stepper Motors
|
|
Hi, everyone. I was wondering if somebody could help me. I am trying to control a 2 phase bipolar stepper motor. I found a web page at : (URL) talks about controlling bipolar stepper motors. But I just can't seem to make it work. When I use the code (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: I have made a i2c routine for the handy board
|
|
i would be interested. thanks (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Bipolar Stepper Motors
|
|
First thing take an ohm meter and "read" your coils. From any wire you should have one other wire at a low resistance and two at a high resistance. This will first determine if you have it wired right. On my steppers the outside two form one coil (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polaroid sonar problems
|
|
(...) I assume that your sonar pings (makes a clicking sound). If so, then you may be getting a premature echo. You might try mounting the transducer in putty to absorb vibration. You could try lengthening the blanking interval to make sure that the (...) (28 years ago, 1-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Scheduler
|
|
Is anybody doing work on the scheduler (tm.c et al)? I've got some ideas for a minor rewrite and don't want to collide with anybody else's efforts. -- No honest business is promoted by spam with the possible exception of Hormel. (28 years ago, 2-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: Polaroid sonar problems
|
|
I also found that my neon light in my magnifying lens lamp caused erroneous readings. When I turned it off or moved it away the readings normalized (gave the correct results). Shielding wasn't effective in this instance. I did completely away with (...) (28 years ago, 2-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Machina Speculatrix Reproduction
|
|
Over fifty years ago W. Grey Walter started building three wheeled, turtle like, mobile robotic vehicles. These vehicles had a light sensor, touch sensor, propulsion motor, steering motor, and a two vacuum tube analog computer. Even with this simple (...) (28 years ago, 2-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Machina Speculatrix Reproduction
|
|
Great post! Thanks. - - - Nick - - - Michael Gasperi wrote: <snip> (...) (28 years ago, 2-Mar-99, to lugnet.robotics)
|
| |
 | | Re: RCX Challenge!
|
|
Hi - I'm new to the group, and intrigued by the challenge. I may just have to try to participate. One thing...that 10 oz can has been bothering me - finally had to go look at my empty Minute Maid Orange can...355 ml, 12 oz. I assume this is what you (...) (28 years ago, 2-Mar-99, to lugnet.robotics.events)
|
| |
 | | Re: Inchworm
|
|
Just when you think you have seen it all! This is really clever. -- Bob Fay The Shop (URL) Beatty wrote in message <36DB08C6.4CBE15B8@a...sk.com>... (...) (28 years ago, 2-Mar-99, to lugnet.robotics)
|