 | | Re: PDF (was Re: legOS docs - what do people want?)
|
|
(...) Hmm... Well, I think it was only earlier today that Markus officially gave his blessing on conversions to other formats (not that we thought he wouldn't, but it seems fair to wait and see for sure). So going by what Markus wrote here: (URL) (...) (28 years ago, 24-Feb-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: PDF (was Re: legOS docs - what do people want?)
|
|
(...) Thank you Todd. I'll work on it tonight and email the pdf back to you sometime tomorrow. (...) (28 years ago, 24-Feb-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: PDF (was Re: legOS docs - what do people want?)
|
|
(...) I'm not sure I'd know what to do with it. I'd be happy to see how it looks on my system, but I think Markus is the destination you want, since he'll be the one hosting it (I assume). --Todd (28 years ago, 24-Feb-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: External Motor Power and the Expansion board.
|
|
ahah, good question. the exp bd grabs the 9v motor power for the servos, sonar, and 9v lego sensors. if you're not using any of these, you could leave connector off the exp bd and you'll have no probs. if these are important, you need to reconnect (...) (28 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | MAX232 Chip
|
|
To all: I am constructing my first Handy board. I am currently building the interface board, but have hit a small 'snag'. While performing 'step 2', installing capacitors and MAX232, and then testing, I did not recieve the correct voltage outputs. (...) (28 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Problem resolved?
|
|
To all, Regarding my previous... I am not sure if it was a soldering connection, but after retesting the output voltages it is very close.. Fred says that the voltages should be between, say, +9 and +10, but I'll get a 8.7.. Is this good enough? If (...) (28 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Contest
|
|
Actually, I believe that the original poster suggested that here be a bonus or award for achieving the goal while limiting their entry to only a single RIS. Based on the ideas that have been flowing in, it sounds doable to achieve the result with a (...) (28 years ago, 24-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest: two motor idea
|
|
Alan Do you have a schematic or diagram of your ideas? What type of gearing would you have to allow two separate gear movements forward and back? Does anybody else have any configurations they've come up with to accomplish the same task? I'm (...) (28 years ago, 24-Feb-99, to lugnet.robotics)
|
| |
 | | RE: External Motor Power and the Expansion board.
|
|
I noticed this to when I built mine, I just bridged the gap I had cut with solder and now use an H-bridge to control the motors. Clancy (...) (28 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Contest Rules
|
|
I can understand the first part of the rule below, but I thought that the cans where to be placed at random, so which can placement rules are you referring to?. "The robot may have knowlege about the number of cans or about rules of can placement." (...) (28 years ago, 24-Feb-99, to lugnet.robotics)
|