To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8871 (+10)
  Re: Adder/Subtractor revisited
 
In article <36B6F795.4B9310A6@n...a.kth.se>, johannes@nada.kth.se says... (...) Ingenious as it is, this thread and previous similar ones have pointed out the primary problems with the A-S drive approach: power transmission through the LEGO (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Re: Adder/Subtractor revisited
 
That sounds very interesting. I hope to see some diagrams or photos soon... Your approach solves the biggest problem introduced by the A-S drive, that of insufficient torque when driving tracks. Two motors is the way to go for tracks. -- SeeYa ! (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Re: Adder/Subtractor revisited
 
In article <F6psw8.Bxy@lugnet.com>, cyberia@erols.com says... (...) Yes, this is the feature that really worked out well. By changing one gear (and adding appropriate number of 1/3 thickness shim plates under the motor), one can get the following (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Re: Adder/Subtractor revisited
 
(...) Actually, I've had pretty good luck with independently driven left and right drive trains; I haven't had a lot of problems with robots curving when I want them to go straight. I find the adder/subtracter useful for a different reason: it makes (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Re: "synchro drive"
 
(...) Wish it was mine. :-) (...) I just used the 12T miter gears. 1:1 with the wheel offset equal to the wheel radius.I was just lucky that it fit the turntable so well. (...) I think the point of this platform is that it's handy to always have a (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
 
  Re: Botcode/SetWatch
 
Chris Magno wrote in message <36BA8C67.5AC1BC47@myna.com>... (...) You can only use SetWatch with values not variables. It would be nice to have control of the display, but the standard code in the RCX doesn't allow it. (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Re: Angle Sensor; 1999 Catalog
 
Issac Merkle wrote in message <19990205140702.9518...il.com>... (...) The internal counter is updated every 3ms. I'm sure the display isn't updated that fast so you won't see every angle on the display. I estimate the RCX can keep up with 1,000 RPM. (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Re: Spirit + C++ Builder - help!
 
(...) I experienced the same problem. It seems to be related to the way C++ Builder handles the Pascal generated Spirit.ocx library, which I have seen suggested was compiled with Borland's Delphi :-/ The filename chosen by C++ builder for the .pas (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  Reading material
 
I've just found a reference in an old robot book to: "Mindstorms", by Seymour Papert ("father" of the RCX) Will have a look at it (two editions: 1980 and 1993) - it's in the university library here - and post another message if it looks good. (...) (28 years ago, 6-Feb-99, to lugnet.robotics)
 
  RE: Dinsmore Compass 1490
 
You say these devices just use hall effect devices to detect the direction, do you have any technical information that would assist in producing a digital compass from scratch ?. Thanks John Hatton mailto:johnhatton@email.com (...) (28 years ago, 6-Feb-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR