To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8716 (+10)
  ROVER
 
Dear Mr Fred Martin, I hope you remember that we in India were making a rover ,which in the end ran into some problems.We had to present the inoperational rover only for the exhibition. Now,after the exhibition we are trying to make the rover work. (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
 
  Re: what variety of 6811 can be used?
 
Hi! (...) Hi Steve! I've put my hb to work yesterday, but I think I can help you a bit. The "FN" means the chip has "plcc" package, while the "P" would mean it's DIP package. The plcc is the one used in the Handy Board, as you can see the 52 pins (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
 
  Re: what variety of 6811 can be used?
 
(...) why does the 512 bytes matter? the HB has 32K of external ram. i guess if you're planning to do rom-able code development then i understand. there's very little difference between the e and a series. the port A counter/timer pins are slightly (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
 
  Pneumatic 6 legged walker
 
For those of you interested in pneumatics I've finally completed a pneumatic 6 legged walker. Included on the page is a small .avi so you can see it walk. CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) you check the web site (...) (28 years ago, 2-Feb-99, to lugnet.robotics)
 
  Re: Pneumatic 6 legged walker
 
Thank you... Have you built pneumatic robots as well? Have you been able to make them strong enough to carry a compressor? CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) bericht----- Van: Barfoot, William: <bbarfoot@tosco.com> Aan: (...) (28 years ago, 2-Feb-99, to lugnet.robotics)
 
  Re: 2 servos
 
(...) Sure is! Check out this page on the HB web site: (URL) Will , , __@_/ \_@__ |/ | /__, o @_/ )\ ) ( \ (\/\\, ~~~...~~~ ' ` ~~~...~~~ ` ~~~...~~~ Wendy Parson, You can't say civilization isn't advancing; Will Bain, in every war they kill you in (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Navigation and PID ressources for Handy Board
 
(...) Francois, That's right, I was trying to use the PID for a control system but I finally gave up due to the small power supply from its motor outputs. The last time I browsed the HB web I did found some articles in the mail list, maybe you can (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
 
  Motor outputs
 
Dear all, I asked this question before but I might have used the wrong wordings. Here I try again. As you all know, the HB 's motor outputs give PVM, however, it gave me problems when I tried to amplify the power (both current and voltage.) Is there (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
 
  Re: 360 deg. swiveling electrical connection
 
I am not familiar with the cyberslam darts... Does it have to be electrical trigger (or are you planning to route something else - a sensor perhaps) ? If mechanical trigger is ok, perhaps you could use a lego axle up the center of the rotary joint. (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
 
  Re: Variations on the "ADDER SUBTRACTOR" ("differtrans" ?)
 
Hey Russell..check out my Geo page..no popup, no obnoxious banner..but hey..I'm sneaky... (...) Joe Greene Technical Support OpenDisc Systems, Inc. Boulder, Colorado, 80301-2442 USA 303-546-0460 Joe_Greene@OpenDisc.Com (28 years ago, 3-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR