To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8656 (+10)
  hall effect sensor
 
hello i use hall effect sensor to check velocity (wheel) of car test(toy) when the wheel stops,that velocity is 0 m/s,i use this value to back my car. using handy board to control it i don't know about connecting hall effect sensor on handyboard. (...) (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
 
  motor/generator observations/thoughts
 
I put together a two wheeled bot today and was showing my son about how one motor could be used as a generator to drive the other motor. Leaving them wired so that one drove the other the same direction, I twisted my bot around on the table, and (...) (28 years ago, 1-Feb-99, to lugnet.robotics)
 
  Re: motor/generator observations/thoughts
 
Janet and Carl McIver wrote (...) Were you using those thick wheels that come with the Mindstorks kit at the front - they limit the steering quite a lot, as I found to my dismay when I tried the 'turnbot' ;) Also - if the RCX was on then the brakes (...) (28 years ago, 1-Feb-99, to lugnet.robotics)
 
  unsubscribe
 
<smaller><smaller>I would like to unsubscribe the mailing list Thank you <nofill> (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
 
  First steps ok
 
Hi! I'm extremely happy today, that I could start mounting my Hand Board. The reset chips arrived and now the only thing that's missing is the lcd, but it should arrive by next Monday. I've mounted the serial comm board and it worked ok, and I've (...) (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
 
  Re: First steps ok
 
Do anyone know who sells handyboards in Italy ? A lot of similar boards, but not the MIT's one. And these other boards are programmable directly with the code written for the handy board ? I think I 'll habve to make the porting. Lucky you who live (...) (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
 
  Re: First steps ok
 
You are right, i was just thinking to do so. I didn't know there were so few resellers, and all so far. Thanks. Stefano. ---...--- (...) (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
 
  Re: HB failure
 
the buzzing indicates that the LCD isn't connected right (or is dead, as you are guessing). first, please be sure that all 14 pins of the LCD are inserted properly into the LCD connector. then (if still probs), try downloading Kent Farnsworth's (...) (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Adder/Subtractor revisited
 
This is not what we did with our models. In the method we, and others have used, you apply the motor power to the carriers of the differentials. There are two possible places to apply the drive force to each carrier (24 teeth or 16 teeth). You do (...) (28 years ago, 1-Feb-99, to lugnet.robotics)
 
  Re: infrared transceivers
 
Would anyone happen to know where I can order infrared transceivers, catalogues, or stores in nyc? (28 years ago, 1-Feb-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR