To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8166 (+10)
  Re: Synchro drive in Lego
 
(...) Well I'd like to control the state of the motors independently so I'm thinking more of a demux (I just aquired 8 more motor kits that were being cleared from Target bringing my total to 10 geared motors and 2 of the older style 9V motors. But (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
 
  WebSpirit
 
I am proud to announce, the release of WebSpirit, which enables you to control the RCX Via the ActiveX Control, and JavaScript, got check it out @ (URL) Ickna / Nick H. | (URL) Ickna@-nospam-aol.com | Remove -nospam- to send | You're not really (...) (28 years ago, 20-Jan-99, to lugnet.robotics, lugnet.general)
 
  Basic to NQC
 
HI: :) I never thought people would take that last bit so seriously. I can live without line numbers. I had to learn to not use them after I got a basic stamp. pervious to that all my programing knowledge came from my glorified microcontroler (an (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Help! Can't talk to IR Tower with Mac w/nqcc!  [DAT]
 
I bought Mindstorms and downloaded nqcc to talk to the RCX, but I can't seem to get connected. I created a cable (actually its a bunch of cables strung together) and confirmed the wiring. I (ultimately) have the following: Mac IR (Male connector) 1 (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Help! Can't talk to IR Tower with Mac w/nqcc!
 
(...) I'm pretty sure that this only happens when the tower is properly communicating with the host PC (in this case, a Mac). At least, mine does, and it works fine. Perhaps you don't have the RCX powered on and in line of sight to the tower? I (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Sharp GP2D05
 
I would like to use the Sharp GP2D05 infrared detection module with HandyBoard. Any hints/suggestions/clues will be highly appreciated. I'm from the PIC generation and am a newbie to the HB and the 68HC11 Thanks in advance, Ranjit (28 years ago, 20-Jan-99, to lugnet.robotics.handyboard)
 
  Battery Level Indicator
 
I have been playing around with trying to make a battery indicator on my Handy Board. I did find the below diagram from a earlier posting in March of 98. BAT --------R1---...---*---...--- Analog5 Input +ve (10K) | (Active) R2 (4K7) | *---...--- Gnd (...) (28 years ago, 20-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Help! Can't talk to IR Tower with Mac w/nqcc!
 
I thought so too. I did have the RCX on at the time. I also checked out the full communications tonight by downloading the firmware using Mindstorms. (A PC @ work is temporarily housing the sw!) so I know that everything else works. This is driving (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  A fast light sensor?
 
Ummm, Hi all I'm looking for a circuit that will interface a photo transistor or a photo diode to a digital input. I tried a photocell in an analog port but it's too slow, I want to use a *visible* light pulse as an accurate trigger: ie. input (...) (28 years ago, 20-Jan-99, to lugnet.robotics.handyboard)
 
  RE: Storage Space
 
I bought a 42 drawer organizer from Home Depot. Normally used for small screws and stuff. The complete Mindstorms kits fits with some extra room to spare. -Kerry -----Original Message----- From: Clay Aucoin [mailto:caucoin@crui...oppes.com] Sent: (...) (28 years ago, 20-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR