To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *7516 (+10)
  Re: Limitations in RCX language
 
I recommend "Gordon's Brick Programmer" as a replacement for the Mindstorms Programming Environment. Tree view based instead of blocks: point and click to add commands, drag to move them, allows variables, and nested loops. No C or Visual Basic (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: 3 sensors = 8 inputs?!
 
(...) Couldn't you do this by simple wire connections? Let's pretend you had a LOT of the motor/sensor connector wires: Sensor #1 is connected to input port #1 hit = 1 0 0 Sensor #2 is connected to input port #2 hit = 0 1 0 Sensor #3 is connected to (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: 3 sensors = 8 inputs?!
 
This would be just fine for digital (on/off) inputs. But it would not do at all for getting more analog inputs. (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  RE: GP2D02?
 
I own an handy-board now for 2 months and I have now 2 GP2D02 connected to it. (took me 1 hour to hook them up and test) You need a digital output-pin(like one off the spi-pins) or make use of the expansion-board, which has digital outputs. I (...) (28 years ago, 7-Jan-99, to lugnet.robotics.handyboard)
 
  (no subject)
 
unsubscribe Thierry VOINIER CNRS-LMA-IM 31, Chemin Joseph Aiguier 13402 Marseille France Tel : 04 91 16 44 73 Fax : 04 91 22 08 75 E-mail : voinier@alphalma.cnrs-mrs.fr (URL) (28 years ago, 7-Jan-99, to lugnet.robotics.handyboard)
 
  RcxCC Joystick controls
 
What do you have in mind? I could add "none" choices when indicating motors fr left and right (or drive ans steer). This would mean that the robot only moves forwards and backwards (or left and right). Would that be what you want? (If you have just (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: RcxCC Joystick controls
 
On my Mindstorms page there is a program that uses the Mindstorms software to steer. Touch sensors turn on the steering motor at power level 1 or 2 (I don't remember which) for 2/10ths of a second per press. It takes 2 taps of the right button to go (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: 3 sensors = 8 inputs?!
 
Mark Crosbie wrote in message <199901070320.TAA020...hp.com>... (...) 3 (...) "logical" (...) This approach can be useful in some applications ofcourse, but theoretically you don't gain more information bandwith. This is because you will be able to (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: Working around the 3 output limitation
 
snip (...) snip You may also want to check this page for a rotating and lifting arm that is controlled by one motor only: (URL) 'Asking directions' from menu Eric Brok Visit LEGO ON MY MIND: (URL) Control section: (URL) section: (URL) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: My "new" rotation sensor
 
(...) Oh, good. I have done some more research hoping to make a really genuine original discovery :) As a few on this list has pointed out the lego light sensor is very receptive to the infrared spectrum. I have found that if I send bursts of (...) (28 years ago, 7-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR