 | | Re: Photoreflectors
|
|
On Wed, 28 Aug 1996, Werner Kuehnert wrote: Hi ! (...) I have been looking at the overhead projector lamps. After my holidays I was planning on test a few for my projects. ---...--- Ed Spike, E&CE Department, University of Waterloo. E2-3357 * (...) (30 years ago, 28-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Charge polarity on each board opposite?
|
|
(...) Do those two boards (Hboard and I/F) have differing requirements of the transformer charge plugs, as the schematics indicate? I have so many wall-warts around, DC and AC, but they all have the return line on the outside. Perhaps it doesn't (...) (30 years ago, 29-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | RE: Charge polarity on each board opposite?
|
|
On a related note, given the power draw of the HB (minimal) would it be practical on some future design to put a small bridge rectifier. This will cost you ~ 1.4 volts (given two diode drops if I calculate it correctly) but has the advantage that (...) (30 years ago, 29-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Charge polarity on each board opposite?
|
|
(...) see the FAQ for an answer to this. (...) did you put the downloader in EEPROM mode before downloading config0c? -Fred (30 years ago, 30-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Modification of RC Servo motor
|
|
I once saw somewere the instructions to modificate a RC Servo motor to make it able to turn continuously. Can anyone point me to a link with such instructions ?? Thanks Oriol (30 years ago, 4-Sep-96, to lugnet.robotics.handyboard)
|
| |
 | | RE: Modification of RC Servo motor
|
|
It varies slightly from servo to servo. Fundemmentally there is a potentiometer that measure the servo position and prevents mechanically the movement . You have to either remove it completely or take out the brush and mechanically (small screw (...) (30 years ago, 4-Sep-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Charge polarity on each board opposite?
|
|
(...) Fred, I use dl on a DOS 286, which does the CONFIG register automatically I thought. In any case, I tried using dl -eeprom config0c.s19, with the same results. The dl of pcode_hb.lis runs nominally, but the LCD remains all black across the top (...) (30 years ago, 5-Sep-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Charge polarity on each board opposite?
|
|
Hi Mike, I'm still out here. Let me know how I can be of assistance. - Prabal (...) (30 years ago, 5-Sep-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Charge polarity on each board opposite?
|
|
(...) right; randy sargent's dl does automatically check the config and burn it if it's wrong. so your config is probably okay. (...) wait; you mean "pcode_hb.S19," right? when it downloads it doesn't give any errors? but the pcode still won't run. (...) (30 years ago, 5-Sep-96, to lugnet.robotics.handyboard)
|
| |
 | | IR
|
|
How does one get the Sharp GP1U52 recievers to acknowledge the 100/125 hz scheme? I've tried using the set_ir_recieve_frequency and ir_counts routines but I only seem to be able to get recognition on port 15. Is there another piece of code that has (...) (30 years ago, 6-Sep-96, to lugnet.robotics.handyboard)
|