 | | Re: IR transmission
|
|
Jeff, You are right. Several things could be wrong here. First of all the precision resistor is VERY VERY important. This controls the frequency of the carrier signal. The freq is approx 1/(RC) where R = R4 and C = C6 of the the Handyboard IR Tx (...) (30 years ago, 8-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR transmission
|
|
Also... For Tx I use a high power IR LED with about a 5-10ohm resistor (I can't remember exactly) Because the carrier is 50% duty and the signal is not continuous, this is ok. If you use a lower powered IR LED and/or a higher resistor, you may find (...) (30 years ago, 8-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR transmission
|
|
(...) Did you tried to remove the resistor? I actually simply fitted the IR diode in the female header. I found that the red diode beside the header would light less if the IR diode is emitting, since those two diode are installed in parallel. The (...) (30 years ago, 8-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | How to add more IC lines?
|
|
Hi, all It appears that the proposed expansion board will not have any additional input capture functions. I've run out of Input Capture lines on the Handyboard, so does anyone have a suggestion on which processor could best be slaved to the (...) (30 years ago, 8-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR transmission
|
|
(...) Well actually, even though it's not a precision resistor, when I installed it, I grabbed a bunch of resistors and measured each one with my DMM until I found one which was between the 3.74 and 3.83 values Fred specified. To further test this, (...) (30 years ago, 8-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
More MUSINGS follow. Seeing as my job gets progressively more MANAGEMENT than TECHNICAL these days - is it really inevitable over the years?? - this software/electronic/mechanical exercise called robotics seems a good hobby to do all those things (...) (30 years ago, 9-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: bootstrap quirk
|
|
(...) Thanks for the suggestion. Unfortunately, the behavior is the same regardless of whether the interface board is connected to my computer. (...) I believe it is working fine, as the previous tests of it were passed. I did have a problem where (...) (30 years ago, 10-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Servo question
|
|
hello everyone I'm playing around with a servo on the HB. i loaded all the progs and got it to twirl, but it won't do a full 180 degrees. i'm just using the servo() command. i suppose servo(1400) is supposed to point it 0degress, but it points about (...) (30 years ago, 10-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Servo question
|
|
(...) You need to go into the servo.c file, and adjust the minimum and maximum frequencies the servo can handle. If you open servo.c, you'll find instructions as to how to do this. You pretty much just have to adjust the program to suit your servo, (...) (30 years ago, 10-Aug-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: piggyback pentium/powerPC
|
|
(...) Try looking for embedded PC systems. The motherboard are sometimes roughly the size of the HB. You may have to buy controller board also to drive a hard drive or a Solid state disk. Expensive stuff! The good thing about some embedded systems (...) (30 years ago, 12-Aug-96, to lugnet.robotics.handyboard)
|