To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6706 (-10)
  legOS Download
 
Has anyone downloaded Markus Noga's legOS files successfully? I keep getting corrupt gzip files. Using Netscape I've tried right clicking and picking "save as", but still seem to get corrupt files. The file size looks right, but all the versions of (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
 
  Re: dc motor output control
 
On my first robot, I just took a resistor in-line and used that. It got very hot, though, and didn't work evenly (some of them must have started to burn out before the others did....) (28 years ago, 22-Dec-98, to lugnet.robotics.handyboard)
 
  Re: I need a poloroid sonar board pinout.
 
Wayne Try this link. (URL) It shows modifications for interfacing the one step board to a microcontroller. I also have an old one step ($1 at a garage sale) but I have not tried the modifications shown for use with the handyboard. I have taken the (...) (28 years ago, 22-Dec-98, to lugnet.robotics.handyboard)
 
  Re: RCX Creator Software v 1.5
 
You got me..:) Your right...i should have said it only requires you to have the OCX installed and registered. Then everything sould work great. Im trying to get the opcodes setup and sending so i can do it natively but thats a bit of work...so maybe (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
 
  Re: RCX port information
 
(...) half the cost of a new RIS, let alone a RCX. But thanks for the link, I'll archive it for now... Jasper (28 years ago, 21-Dec-98, to lugnet.robotics)
 
  RE: expansion board - servo control
 
-----Original Message----- From: shsc9801@condor.stcl...dstate.edu [mailto:shsc9801@con...state.edu] Sent: Monday, December 21, 1998 1:39 PM To: handyboard@media.mit.edu Subject: expansion board - servo control Hi, I stopped working with the (...) (28 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
 
  expansion board - servo control
 
Hi, I stopped working with the handyboard for a while but just started back up again. I put the expansion board onto my handyboard and began testing it. After testing the general tests done before with just the handyboard I started testing the servo (...) (28 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
 
  Re: RCX port information
 
(...) I should clarify this before anyone breaks their RCX. The pins are 99% definitely unused. By the ROM driver. They might, however, be tied to Vss or Vdd, so make sure you don't short anything out if do attempt to solder something to the extra (...) (28 years ago, 21-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
Linc Smith wrote in message ... (...) I went to the model store, and picked up small diameter silicon tubing used for fuel systems in RC models. To be honest I stopped looking after feeling the silicon tubing, so I didn't investigate the gum (...) (28 years ago, 21-Dec-98, to lugnet.robotics)
 
  Fw: CdS Light Sensor
 
Shame on me. I should have read the thread more carefully - my bad. trowt -----Original Message----- From: Barry Bott <barry.bott@virgin.net> To: lego-robotics@crynwr.com <lego-robotics@crynwr.com> Date: Monday, December 21, 1998 11:53 AM Subject: (...) (28 years ago, 21-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR