To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6631 (-10)
  Re: All-around-the-robot bump detection
 
Like I said, just ideas, and I haven't yet woken up. Thoughts ? I like the pneumatic idea, but instead of using a cylinder, how about taking a piece of Lego tubing and bending it, so that when you have pressure in the system, the tube wants to (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: ROM stuff: Better than PWM
 
(...) Funny - I was thinking of doing exactly the same thing - and also basing it on Bresenham. I've always wondered about 1-bit D/A, but if you actually read the docco it is wrapped up in so much weird signal theory it is very hard to understand (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  ROM stuff: Better than PWM
 
So I was thinking about writing a motor driver that is better than what is in the ROM already. Here's the problem: You have a function called once every 1/1000th of a second. You want to allow n speeds of the motor at minimal cost in lookup tables. (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: dc motor output control
 
Maybe you can put a series of diodes in series and in parallel but the other direction to reduce the voltage. H-bridge +- +- +- +- motor H-bridge -+ -+ -+ -+ Good luck, James (...) (28 years ago, 19-Dec-98, to lugnet.robotics.handyboard)
 
  RE: urgent request help !!!!
 
What about the display board itself? Could it be that one of the SMT parts on the board is dead? Or a trace on the LCD is shorted? --phil (28 years ago, 19-Dec-98, to lugnet.robotics.handyboard)
 
  Re: Question for you Technic pros
 
Hi: (...) The cross axle w/ eyes (Lego's name, not mine!) was in only 1 technic set, the small front end loader 8235 (1995). It differs from the two tie rods in that the tie rods can accept a ball joint but the axle w/ eyes cannot. The cross axle (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
(...) Hello... Your logging machine sounds like a great model. I hope you're able to show a bunch of detailed pictures in the future. <ICS> (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Question for you Technic pros
 
Linc Smith wrote in message ... (...) that (...) I'm not quite sure to which part you are refering at the above site, unless you are talking about the "rack w/ tie rods" which is still quite different from the cross axle w/ eyes #16. But now that I (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: urgent request help !!!!
 
-----Original Message----- From: phillip chia [mailto:philchia@sin...et.com.sg] Sent: Friday, December 18, 1998 7:04 AM To: handybd Cc: Mr Peter Lim Subject: urgent request help !!!! Hi Fred and others, I very desperate to debug the problem that (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
 
  Re: Question for you Technic pros
 
John, if I am thinking of the same piece (cross axle w/ eyes #16, 1995) that can be found at (URL) I am aware of at least two very similar piece that is 6 studs (fairly sure) long. They are meant to accept a ball to form a ball-joint. Check out (URL) (28 years ago, 18-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR