 | | RE: Air Tank overload??
|
|
I would guess it would be more likely to damage the rubber tubes that are connected to the tank. It could possibly cause them to burst, or "bubble", or maybe just pop off of the tank. The tank itself seems very solid to me. Eric -----Original (...) (28 years ago, 12-Dec-98, to lugnet.robotics)
|
| |
 | | RE: Air Tank overload??
|
|
(...) Or if you're especially ambitious, you could glue a stress gage to the tank, and run it through a Wheatstone bridge to your RCX. :) Someone recently posted, either here or on RTL, that they used a film canister (with the lid glued on) for a (...) (28 years ago, 12-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CyberMaster in North America ??
|
|
Nick Taylor wrote in message <36713BE3.A8FD1C5D@i...me.com>... (...) No, but it's not too hard to get someone to buy one and send it to you. Me, for instance :) Or go thru Busy Bee in the UK. They're $NZ400 here, which works out at $US210, then (...) (28 years ago, 11-Dec-98, to lugnet.robotics)
|
| |
 | | The 9V Motor (#5115)
|
|
I was wondering if you can use the "older" 9V Motor with the RCX as a third output motor. Will it damage the RCX and/or motor? (28 years ago, 12-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CyberMaster mail order in UK ??
|
|
(...) I'm going to warn you on something you might not be aware of: LEGO in the United Stated is far cheaper than in the Europe. For instants, in the UK MindStorms is sold at $270 (£160) at Toys "R" Us. That's why we go to the States to buy a (...) (28 years ago, 12-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CyberMaster in North America ??
|
|
At 23:56 11-12-1998 Friday , you wrote: Nick Taylor wrote in message <36713BE3.A8FD1C5D@i...me.com>... (...) I'm going to warn you on something you might not be aware of: LEGO in the United Stated is far cheaper than in the Europe. For instants, in (...) (28 years ago, 12-Dec-98, to lugnet.robotics)
|
| |
 | | Source of 68HC11 in UK?
|
|
Does anyone know of a supplier for the 68HC11 in the UK? Also any handyboard suppliers in UK. Peter (28 years ago, 12-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Air Tank overload??
|
|
In article <3671BD48.C514686E@gte.net>, Kevin A. Saddi <ksaddi@gte.net> writes (...) I use a pneumatic actuator retrained with rubber band. When pressure is high enough it makes a contact (wire in foil on the moving arm and similar on a lego brick (...) (28 years ago, 12-Dec-98, to lugnet.robotics)
|
| |
 | | config download problems
|
|
Hi I am building a handyboard from scratch after finding it on the net. I actually purchased two pcb's from Douglas Electronics. An aside, they were great to deal with answering all my questions promptly and efficiently. I built the first hb and had (...) (28 years ago, 12-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: RCX port information
|
|
Hi Scott, there is lots of technical info available. The H8/3297 series hardware manual is probably what you're looking for: (URL) pdf version is available on the same site. More specifically, the microcontroller has 8 A/D input pins. Right now, (...) (28 years ago, 12-Dec-98, to lugnet.robotics)
|