 | | Keeping the piece(s)
|
|
Hi, I'm relatively new to this group. I've been lurking for the past month or so. I was wondering what you all use to keep all your pieces together. I have two RIS kits and expansion packs, and the boxes they come in seem to be an awful waste of (...) (28 years ago, 8-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Serial interface/ RF data link
|
|
To properly comunicate with any PC you need to convert your TTL TX and TTL RX signals coming from the Handy Board to RS232 voltage levels. The charging board contains this interface IC called the "MAX232" The power wire is required unless you are (...) (28 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | persistent var's in IC
|
|
Has anyone had problames with the Handyboard, IC 3.2 and 'persistent' variables? the following declaration works fine : persistent float i; but using an array: persistent float battery_voltage[ 320 ]; always causes an error while downloading : IC> (...) (28 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: Serial interface/ RF data link
|
|
<<snip>> Unfortunately, I have not had any luck. This brings me back to the first point- is it possible to use the serial interface board by just providing the tx and rx lines? <<snip>> In short, no. The serial interface board takes power from the (...) (28 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: Keeping the piece(s)
|
|
Personally, I've gone a little nuts. I spend 80% of my 'lego time' sorting pieces. Bought two large tackleboxes. One's motors, sensors, rods, connectors and funky pieces. The other's for the small pieces, like 2x1 blocks & flat lengths. I use three (...) (28 years ago, 8-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Keeping the piece(s)
|
|
(...) I have about 6 "RubberMaid" tubs that contain all of my current pieces. Each box has a "topic" being Technics, Standard Legos, Special Legos, bases, etc... I am soon going to get a set of "Sandwich Keepers" to keep together very special pieces (...) (28 years ago, 8-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Keeping the piece(s)
|
|
Hossepian, Nishan wrote in message (...) <snip>... (...) have (...) Check out the Lugnet.storage group: Sorting and storage methods/systems for elements, instructions, catalogs, boxes, etc. (URL) many sorting ideas and a good survey of what other (...) (28 years ago, 8-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Keeping the piece(s)
|
|
(...) [...] Home Depot has plastic part bins and tool boxes of all shapes and sizes. The one I chose is about the size of a thick briefcase and is divided into four rows which can be subdivided with small plastic partitions as desired. The great (...) (28 years ago, 8-Dec-98, to lugnet.robotics)
|
| |
 | | RE: Help with overcharged batteries
|
|
<<Last night we discovered that we had left our Handyboard on ZAP when we thought <<we had left it to trickle. It was left at this condition for about 6 hours. You probably should remove the battery pack, put it in a baggie, and take it to Radio (...) (28 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Keeping the piece(s)
|
|
(...) etc... (...) Ziploc also sells a bunch of half height snack bags that are great for holding bits like axels, connectors, and other tiny bits. I have found that the best way to store the larger bricks is by stacking them together in blocks of (...) (28 years ago, 8-Dec-98, to lugnet.robotics)
|